9F燃机启动调试步骤.docxVIP

9F燃机启动调试步骤 9F燃机启动调试步骤 9F燃机启动调试步骤 Day/Date 天/日期  Test 试验  Purpose of Test 试验目的  Test activities 试验活动 Remarks 备注 Day 1 第 1 天 11/08/2006  Rotor run- in: 转子试 转： Crank test 摇转试验  1. Listen for rubs or unusual noises 听能否有摩擦和异样噪音 2. Functional test of emergency trip button 紧迫跳闸按钮的功能试 验 3. Purge speed cranking for rotor  Roll up to 50 rpm trip by DCS emer-gency push button and 200 rpm and trip by GT MK 6 control emergency stop 通 过 DCS 紧迫按钮渐渐增添到 50rpm，经过 GT MK6 控制紧迫停机跳闸  Use auto start-up sequences to prepare the unit for a “-Readyto-Start 采”用自动走动次序将机组准备好“准备起动” Rub checks are performed检查摩擦 ADRE vibration monitor to be connected 连结 ADRE 振动监督器 vibration check 以吹扫速度摇 转，检查转子振动状况 4. Monitor LCI starting tempera- tures and operation监督器 LCI 起动温度和运转 5. Air blowing the purge piping of D5 and PM4 gas fuel during crank 摇转时期给 D5 和 PM4 吹 扫管鼓风 6. Check operation of lift oil and turning gear 检查顶轴油和盘车 的运转  2. Restart, accelerate to go to Purge speed After Shut-down 停机后 for 5min and select normal stop 重起， ? Reinstate the piping spool of D5 and PM4 加快到吹扫速度 5 分钟，选择正常停 pipe work after shutdown 停机后从头恢 止 复 D5 和 PM5 管子的导管 Restart, hold at purge speed and air blowing the piping of D5 and PM4, trip by DCS customer trip (L4CT) after 30 Min crank test 重起，保持在吹扫速度，给 D5 和 PM4 管道鼓风，在 30 分钟摇转试验后经过 DCS 客户跳闸（L4CT ）跳闸 Verify coast down to turning gear 核实惰行至盘车 Monitor vibration levels through out the test period监督整个试验时期的振动 级 Day 1 第 1 天 11/08/2006  Rotor run- in: 转子试 转： False fir-ing, actual first firing and FSNL 假点火， 实质第一 次点火和 FSNL  False fire 假点火 Actual First Fire to FSNL 实质第一次点火至 FSNL  Select fire for false fire and check unit for gas leaks, and P2 pr. Check 选择假点火的火，检查机组能否漏气，和 P2。检查 Verify unit trip and coast down to turning gear 核实机组跳闸，惰行至盘车 Actual first firing and check for gas leaks at firing speed 实质第一次点火，检查点快速度时能否漏气 Acceleration unit up to FSNL and stabilized min 4 hours thermal soak Start up heater commissioning将机组加快到 FSNL，起码稳固 4 小时热浸泡 Normal down unit and keep turning gear on for natur