流程管理线路板流程术语中英文对照.docxVIP

流程管理线路板流程术语中英文对照 线路板流程术语中英文对照 流程简介：开料－－钻孔－－干膜制程－－压合－－减铜－－电镀－－塞孔－－防焊(绿漆/绿油) －－镀金－－喷锡－－成型－－开短路测试－－终检－－雷射钻孔 A. 开料( Cut Lamination) a-1 裁板( Sheets Cutting) a-2 原物料发料(Panel)(Shear material to Size) B. 钻孔(Drilling) b-1 内钻(Inner Layer Drilling ) b-2 一次孔(Outer Layer Drilling ) b-3 二次孔(2nd Drilling) b-4 雷射钻孔(Laser Drilling )(Laser Ablation ) b-5 盲(埋)孔钻孔(Blind Buried Hole Drilling) C. 干膜制程( Photo Process(D/F)) c-1 前处理(Pretreatment) c-2 压膜(Dry Film Lamination) c-3 曝光(Exposure) c-4 显影(Developing) c-5 蚀铜(Etching) c-6 去膜(Stripping) c-7 初检( Touch-up) c-8 化学前处理,化学研磨( Chemical Milling ) c-9 选择性浸金压膜(Selective Gold Dry Film Lamination) c-10 显影(Developing ) c-11 去膜(Stripping ) Developing , Etching Stripping ( DES ) D. 压合 Lamination d-1 黑化(Black Oxide Treatment) d-2 微蚀(Microetching) d-3 铆钉组合(eyelet ) d-4 叠板(Lay up) d-5 压合(Lamination) d-6 后处理(Post Treatment) d-7 黑氧化( Black Oxide Removal ) d-8 铣靶(spot face) d-9 去溢胶(resin flush removal) E. 减铜(Copper Reduction) e-1 薄化铜(Copper Reduction) F. 电镀(Horizontal Electrolytic Plating) f-1 水平电镀(Horizontal Electro-Plating) (Panel Plating) f-2 锡铅电镀( Tin-Lead Plating ) (Pattern Plating) f-3 低于 1 mil ( Less than 1 mil Thickness ) f-4 高于 1 mil ( More than 1 mil Thickness) f-5 砂带研磨(Belt Sanding) f-6 剥锡铅( Tin-Lead Stripping) f-7 微切片( Microsection) G. 塞孔(Plug Hole) g-1 印刷( Ink Print ) g-2 预烤(Precure) g-3 表面刷磨(Scrub) g-4 后烘烤(Postcure) H. 防焊(绿漆/绿油): (Solder Mask) h-1 C 面印刷(Printing Top Side) h-2 S 面印刷(Printing Bottom Side) h-3 静电喷涂(Spray Coating) h-4 前处理(Pretreatment) h-5 预烤(Precure) h-6 曝光(Exposure) h-7 显影(Develop) h-8 后烘烤(Postcure) h-9 UV 烘烤(UV Cure) h-10 文字印刷( Printing of Legend ) h-11 喷砂( Pumice)(Wet Blasting) h-12 印可剥离防焊(Peelable Solder Mask) I . 镀金 Gold plating i-1 金手指镀镍金( Gold Finger ) i-2 电镀软金(Soft Ni/Au Plating) i-3 浸镍金( Immersion Ni/Au) (Electroless Ni/Au) J. 喷锡(Hot Air Solder Leveling) j-1 水平喷锡(Horizontal Hot Air Solder Leveling) j-2 垂直喷锡( Vertical Hot Air Solder Leveling) j-3 超级焊锡(Super Solder ) j-4. 印焊锡突点(Solder Bump) K. 成型(Profile)(Form) k-1 捞型