换热器计算表.xls

Sheet3 Sheet2 Sheet1 Tube Side Shell Side Connected Pipeline Volecity for Shell (m/s) Diameter of Connected Pipeline for Shell (mm) Connected Pipeline Volecity for Tube (m/s) Diameter of Connected Pipeline for Tube (mm) Equality Diameter for Shell (m) Section Area for Shell (m2) Volecity for Shell (m/s) Re (Shell) Pr (Shell) Section Area for Tube (m2) Volecity for Tube (m/s) Re (Tube) Pr (Tube) Film Coef. for Tube (w/m2.C) Film Coef. for Shell (w/m2.C) Wall Resis of Tube (w/m.C) Dirty Heat Transfer Coef. (w/m2.C) Fouling Resis for Shellside(m2.C/w) Fouling Resis for Tubeside (m2.C/w) Calculated Heat Transfer Area (m2) Actual Heat Trabsfer Area (m2) Surplus Area % Tm tm Temp. Of Tube Wall (C) Temp. Of Shell Wall (C) Diff. Temp. Between Shell-wall and Tube-wall Relative Roughness of Tube li DeltPo of Shellside DeltPi of Shellside DeltPs of Shellside M12 Selected Dia. Of Connected Pipeline for Shell (DN) Selected Dia. Of Connected Pipeline for Tube (DN) Selected Tubeside Inlet Temp. DeltPi of Tubeside (Mpa) DeltPr of Tubeside (Mpa) DeltPt of Tubeside (Mpa) F (Tube Arrangement Form) Fs of Shell (Fouling Coef.) Heat-exchanger Capacity Checking Wall Temp. Pressure Drop 换热器计算表 原始资料 项目 流率 (kg/h) 进口温度 (C) 出口温度 (C) 应力(Mpa(G)) 设计温度 (C) 密度(kg/m3) 比热 (kj/kg.C) 粘度 (Pa.s) 导热系数 (w/m.C) 热负荷(Kw) 平均温差(C) 初步估计传热面积 假设K (w/m2.C) 传热面积 (m2) 估计面积系数 初估传热面积 (m2) 换热器计算尺寸 选择管径 (外) (mm) 管壁厚 (mm) 管口流速 (m/s) 单程管数 取单程管数 计算管长 (m) 取管长 (m) 计算管程数 选管程数 总管数 校正系数R 校正系数P 温差校正系数. 传热器平均温差. 管间距 (mm) 取管间距 (mm) 分程间距 (mm) 管板利用效率 壳程内径(mm) 选内径 (mm) % 折流板开孔 折流板间距 (mm) 折流板数 选折流板数 拉杆直径 拉杆孔径 899688.42 3600.00 227801.00 29.00 110.00 39.00 60.00 .40 6.90 34.00 2.00 85.00 2.00 994.30 90.00 4.17 3.30 7.42E-04 1.50E-05 .62 .03 10431.39 3600.00 10431.39 3600.00 48.27 360.00 600.31 1000.00 1.15 690.35 25.00 2.50 1.30 615.43 3600.00 1000000.00 3.14 2.00 2.00 4.00 616.00 14.27 3.14 1.00E-03 7.00 2.04 2.00 1232.00 5.00 .12 .96 46.34 31.25 1.25 32.00 44.00 2.00 2.00 6.00 .70 1409.60 1.05 1450.00 25.00 450.00 14.56 1000.00