JBT 3411.83-1999锥柄90°镗刀杆 尺寸.pdf

ICS 25.080.01J52JB中华人民共和国机械行业标准JB/T 3411.83—1999锥柄90°镗刀杆尺寸Taper shank arbor for 9o°boring toolDimensions1999-05-20发布2000-01-01实施国家机械工业局发布 中华人民共和国机械行业标准JB/T 3411.831999锥柄90°镗刀杆尺寸Taper shank arbor for 90° boring tool代替JB3494—83-Dimensions1范围本标准规定了锥柄90°鐘刀杆的型式和尺寸。2引用标准下列标准所包含的条文，通过在本标准中引用而构成为本标准的条文。本标准出版时，所示版本均为有效。所有标准都会被修订，使用本标准的各方应探讨使用下列标准最新版本的可能性。GB/T1443—1996机床和工具柄用自夹圆锥GB/T 2815—1989钻床主轴端部尺寸3型式和尺寸型式和尺寸按下图和表的规定。标记标记示例：莫氏圆锥5号，D=50mm，L=450mm的维柄90°鐘刀杆：鐘刀杆5-50X450JB/T3411.83—1999医馆LeL国家机械工业局1999-05-20批准2000-01-01 实施 JB/T 3411.83—1999圆号DDs莫氏米制基本尺寸极限筛差D11bi2532~488+0.1308.5332406010 +0.04010.540 48~7512 +0.160+0.050120.1308.5432 406010+0.04010.540 487512+0.16012.550609516+0.05016.532406010+0.130+0.04010.540 487512+0.16012.5550609516+0.05016.56072~1158095~1500z+0.19521.0100 120~19025+0.06526.032406010 +0.130*0.04010.540 487512 +0.16012.5650 609516+0.05016.56072~1158095~15020 +0.19521.0100120~19025+0.06526.040 487512 +0.16012.050 609516+0.05016.06072~1158080+0.19521.095~150+0.065100120~1902526.0120150~23032 +0.240+0.08033.050 609516 +0.160+0.05016.56072~115100 8095~15020+0.19521.0120~190+0.065100 2526.0120 150~23032 +0.240160200~300+0.08033.0注莫氏圆与米制圆维的尺寸和确差按GB/T1443的规定。当刀孔尺寸5≤10mm，b，≤10.5mm时，方刀孔允许改成圆刀。当D≥60mm、L≥560mm时，杆部允许制成至型。N JB/T 3411.83—1999mm082315355400450500560630710800L186.0306.0221.0356.0186.0306.0-406.0162.5282.5197.5-332.5162.5282.5一382.5237.5一332.5一512.5-350.5480.5205.5410.5560.500480.5650.5165.5205.5190.0-350.0240.0一500.0190.0一290.0420.0590.0240.0350.0500.0690.0190.0410.0230.0340.0490.0410.0580.0340.0一490.0180.0300.0 450.0190.0一370.0560.0000450.0一640.0140.0190.03 JB/T 3411.83—1999附录A（标准的附录）工具锥柄锁紧槽尺寸A1图A1和表A1所列工具锥柄锁紧槽尺寸，系按GB/T2815及国内常用普通钻、鐘床编制的。L,删量线$图 A1表A1mm、阿雕号莫氏345代号米5.06.5 6.58.08.0 10.012.0外25.025.035.045.055.0 60.070.0L;30.035.040.0 40.0 45.052.0 60.0 86.68.2 12.216.219.326.332.3内30.030.040.050.0 60.070.080.0 L30.035.0 40.040.045.0 52.060.0 86.68.212.216.219.326.332.3 JB/T 3411.831999附录B（标准的附录）锁紧楔尺寸B1图B1和表B1所列锁紧楔尺寸，系按GB/T2815及国内常