JBT 9163.10-1999压帽式剃珩齿心轴 尺寸.pdf

ICS 25.080.01J52JB中华人民共和国机械行业标准JB/T9163.10—1999压帽式剃珩齿心轴尺寸Mandrels with press-cap for gearshaving machine or gear honing machineDimensions1999-05-20发布2000-01-01实施国家机械工业局发布 中华人民共和国机械行业标准压帽式剃齿心轴JB/T 9163.10—1999尺Mandrels with presscap for gear代替 ZB J52 002.10—87shaving machine or gear honing machineDimensions1范围本标准规定了压幅式剃齿心轴的型式和尺寸，适用于加工定位直径为12～80mm的齿轮。2型式和尺寸型式和尺寸按下图和表的规定。d≤20mmGB/T.308198920mm表mm国家机械工业局1999-05-20批准2000-01-01 实施 JB/T 9163.10—1999~基本尽寸极圈偏差h6Lar 12 3582 50 97133582509735821455102 15 0358201640 32.1787656112 17 40 87651121840 887512340198875123 20 40 887512321 50 1028013222 50 102 801322350 102-050 102 24 801325538.451079014226 551079014228 6011295147OE6012795162N JB/T 9163.10—1999表(续)基本尺寸极限偏差951626012734 951627036140110180OL1403811018040 14001101800.0169042 1601201909045160130200901604613053.4520090951624814521790162 50 14521790162 52 14521710053 1751502255610017501502250.0191106018516524012019062 175250631201951752503 JB/T 9163.101999表(完)mm基本尺寸极限偏差 Lrrh6 671201951752501302057118526013020572 04526075130205190265140215802002753标记标记示例：d=20 mmv=75mm的压相式行齿心轴的标记：心轴20X75JB/T 9163.10—1999 JB/T 9163.10—1999附录A(提示的附录)有工艺余量的心辅直径尺寸本附录所列I、Ⅱ两种心轴直径尺寸为参考数值，是根据工件定位孔在工序间的加工余量确定的，主要供工序间加工使用。mm基本尺寸工艺余量心轴直径尺寸基本尺寸工艺余量心轴直径尺寸dII极限筛差h6dII极限偏差h612 11.8011.603635.8035.601312.8012.60837.8037.601413.8013.6040 39.8039.601514.8014.60[10°0042 41.8041.6008015.6045 44.8044.601716.8016.604645.8045.601817.8017.6048 47.8047.6019 18.8018.6050 49.8049.5020 19.8019.6052 51.8051.502120.8020.6053 52.8052.5022 21.8021.605655.8055.502322.8022.6006059.8059.502410°0-23.8023.6062 61.8061.502524.8024.606362.8062.50610°09元25.8025.606766.8066.502827.8027.607170.8070.5030 29.8029.6072 71.8071.503231.8031.607574.8074.503433.8033.600.0168079.8079.505 JB/T 9163.101999中华人民共和国机械行业标准压帽式剃齿心轴尺寸JB/T 9163.10—1999机械工业部机械标准化研究所出版发行机械工业部机械标准化研究所印刷（北京首体南路2号*开本880X12301/16印张X/X字数xXX,xXX19XX年xX月第x版19XX年XX月第x印喇印数1XXX定价xXX.XX元编号XX-XXX