JBT 2001.73-1999水系统 45°锯齿形螺纹 牙型与基本尺寸.pdf

ICS 23.100J 20JB中华人民共和国机械行业标准JB/T 2001.73—1999水系统45°锯齿形螺纹牙型与基本尺寸Water system—45 degree sawtooth threadTooth pattern and basic size1999-06-28发布2000-01-01实施国家机械工业局发布 中华人民共和国机械行业标准水系统45°锯齿形螺纹JB/T 2001.731999牙型与基本尺寸代替 JB 2076—84Water system—45 degree sawtooth threadTooth pattern and basic size范围本标准规定了45°锯齿形螺纹牙型与基本尺寸。本标准适用于压力机立柱用45°锯齿形螺纹。2：型式与尺寸2.1牙型按图1及表1的规定。2.2基本尺寸按表2的规定。外放H-r e=0.25 r 20.02 0.16 h,=0.575 0.1751 r=/V2h=0.5 r f,e0.25 r图 1表 1外:纹[间限内纹螺文高度齿顶宽度圆角半径倒角z螺纹高度齿顶宽度圆角半径倒角xmm63.451.500.740.53.01.780.40.584.602.0 0.99 0.5 0.324.0 2.320.4 0.5 105.752.501.241.00.365.02.860.81.0126.903.01.491.00.406.03.400.81.0169.204.0 1.981.00.488.04.480.81.02011.505.0 2.481.50.5610.0 5.56 1.21.52413.806.02.971.50.64 12.06.641.2 1.53218.408.03.961.50.8016.08.801.21.84023.0010.04.951.50.96 20.010.961.2 2.0国家机械工业局1999-06-28批准2000-01-01 实施1 JB/T 2001.73—1999表 2内外螺纹外螺纹内螺纹螺距外径内径内径内径外爆纹截面积Fdddicmmm150147143.1144160.8160157153.1154184.1OL 1167163.1164 208.9180LL1173.1174 236.3190187183.1184263.3200196190.8192 28500z202316.596220216210.8212 348250246240.8242455.4280275268.5270566.210 300295288.5290653.7315308.5310747.1350344336.2887.312 380PLE3667400 3923817420412 401.6404 1266.116 450442 4310480472461.6464 1672.6500492 4816520510497.0500 1939.0550540 527.0530 2180.220 580570557760059057786206105978650638622968066865227006886722247207086923750738722.47268607807687529N JB/T 22001.73—1999表2(完)内外螺纹外螺纹内螺纹螺距外径内径内径内径外螺纹截而积Fdddicmmm80078476368208047832850834813.2818861S880864843.28t85580.632 900884863192090488300569237980964943.29488°186910009849636106010401014.010208075.4112011001074.01080r6S0640 118011601134.0114010099.9125012301204.0121011385.33标记与示例3. 1液压机用45°锯齿形纹用字母“YS直径×螺距/线数螺旋方向”表示，单线螺纹不必注明线数，右旋蝶纹不必注明螺旋方向。3. 2标记示例例1：螺纹外径250mm，螺距8mm左旋单线锯齿形螺纹：YS 250X8左JB/T 2001.73—1999例2：螺纹外径300mm，螺距10mm右旋单线锯齿形螺纹：YS 30