QB 1221-1991自行车英制螺纹和量规.pdf

中华人民共和国行业标准QB 1221--91自行车英制螺纹和量规本标准参照采用国际标准ISO 1502《IS0普通米制螺纹-检验》，IS06698《自行车飞轮与后轴装配的螺纹》。主题内容与适用范围本标准规定了自行车用的各种成品件上的英制螺纹的基本牙型、基本尺寸、公差与基.本偏差，并规定了自行车用英制螺纹的量规及其制造尺寸。本标准适用于自行车用的英制螺纹。也适用于检验本标准中规定的英制螺纹尺寸和公差.用的螺纹量规。2 引用标准GB 192普通螺纹基本牙型GB 196　普通螺纹　基本尺寸GB 19？普通螺纹公差与配仑GB 2515普通螺纹术语GB 2516普通螺纹偏差表GB 3934普通螺纹量规3自行车英制螺纹3.1基本牙型PH =V8/2P = 0.866025404PP5H/8 = 0 541265877PNr1o3H/8 = 0.324759520PH18601H/4 = 0.216506351PHj81H/8 = 0.108253175P30D = D-2 × 3H/8三4IDd,= d--2× 3H/82号D, = D -2 × 5H/8d1= d-2× 5H/8螺纹轴线d2一外螺纹中径，D--内螺纹大径,d一外螺纹大径;D2-内螺纹中径,P一螺距H一原始三角形高度di一外螺纹小径，D,~-内螺纹小径,1992—04-—01实施中华人民共和国轻工业部1991—09-10批准-36- QB 1221—913.2螺纹牙底形状螺纹牙底形状应符合GB197中 9，10，11章的有关规定。3.3基本尺寸（见表1）表1mm大中公称尺寸每英寸牙数径径小径应用举例int.p.i.D或dDz 或 dzDi或d,0.317*268.0527.4176.994前轴棍、前轴母.- .260.379*9.6399.0048.581后轴棍，后轴母0.413*. 2610.5009.4429.865脚阑后轴棍、左大挡200.50012.70011.87511.325脚避轴、曲柄(E型)0.5682014.43713.61213.062脚避轴、曲柄1.0052425.52324.83624.378前叉、土挡1.295*2432.893脚阑右大挡32.80631.7471.3752434.92534.23833.780中轴碗、中接头、后轴身、飞轮注：带者为推荐使用。3.4极限尺寸和公差3.4.1外螺纹极限尺寸和公差（见表2）表 ¥2nmd公称尺寸大径中径dz每英寸牙数小径d公差带int.P.i.最大差差最最大公最小最大公小0.317266g6e7.9920.1807.2796.8627.8127.3910.1120.379266g6e9.5790.1809.3998.9780.1128.8668.4490.413266g9.31010.4740.1809.8390.1129.72710.2940.500206g12.6720.21212.46011.71511.8470.13211.1600.568206g6e14.3740.21214.16213.5840.13213.45212.8971.005246g25.4970.18025.31724.8100.12524.68524.2371.295246g6e32.8330.18032.65332.1800,12532.05531.6081.375246g34.8990.18034.71934.2120.1253.1.08733.6391.375246g8e34.8650.28034.5353.1.2120.12534.08733.639-37-- QB 1221-913.4.2内螺纹极限尺寸和公差（见表3）表3mmD,D2径中径小大径D公称尺寸每英寸公差牙数差差最小最大公最小带最小最大公int.P.i.6.9947.2300.2360.1507.417266H8.0257.5670.3178.5818.8170.236+--6H9.1540.1509.004269.6390.3799.6780.2369.4426H0.1509.8652610.50010.0150.41311.5900.26511.3250.18011.875206H12.70012.0550.50013.3270.26513.06213.7920.18013.612206H14.437:0.56824.6140.23624.37824.8366H25.52325.0060.1701.0052431.74731.9830.23632.3760.17032.2061.295246H32.89333.78034.0160.2366H34.4080.17034.2382434.9251.375螺纹标记：本标准的螺纹标记应符合如下规定。B符号后面