工时制定及绩效观念课件.pptVIP

A-DATAConfidential标准工时制定及绩效观念主讲人:张亚平（28343）1Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential2Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential3Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential3.在计量化基准数据之中，“标准工时”一直占有一份不可替代的重要地位。4Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential5Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential6Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential标准工时制定7Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential1.走行：平均体力的男子，不带任何负荷，在平坦道2.路上行走，速度为4.8公里/小时。3.插销子：将30只销子插入到30只孔内，用24.6秒。9Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential11Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential依各制程不同会给予不同标准,电子业和机械制造业就会有不同宽放比率。12Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential用马表量测压合工站作业员的平均工时为3.7S，作业员的评比率为110%，该压合工站的合计宽放率为10%，则该站的正常工时为多少S，标准工时为多少S？13Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential作业测定介绍14Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential15Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential20Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential生产线平衡定义：组装生产线的各工程的作业时间几乎相同，就表示生产线平衡了。生产线则讲究整体绩效，整体绩效的关键在于整线的瓶颈工作站。21Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential一般不平衡率的范围在5%~15%之间，如果高于15%，就要改善了。22Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential23Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidentialPD线前段有点胶、后焊、裁板、初测、组装、压合6个工作站,其标准工时分别为5秒,6秒,7秒,8秒，9秒，10秒。(1)PD线前段的C.T取最大工时站=10秒(2)PD线前段的总作业工时=5+6+7+8+9+10=45秒(3)PD线前段的标准工时为=10X6=60秒(4)PD线前段的平衡率:24Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential25Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential26Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential=(生产数量X标准工时)/直接投入工时=(生产数量X标准工时)/(直接投入工时-除外异常工时)27Copyright?2007A-DATA.Allrightsreserved.

A-DATAConfidential28Copyright?2007A-DATA.Allrightsreserved.

A-DATA