单片机用C语言设计跑表,由按键控制(用中断).docVIP

单片机用C语言设计跑表，由按键控制(用中断） 2009-07-08 16:50 是四个数码管，跑表程序，硬件上按键为三行四列，从上往下从右往左依次为 ?????????? * 7 4 1?????????? 0 8 5 2?????????? # 9 6 3跑表设计1.按*开始时钟计数格式，第一格10S，第二格1S，第三格0.1S，第四格0.01S，前两者为60进制，后两者为100进制2.当按0——9中任何一个数，即把当前的时钟值存储下来3.按#停止计时，此时按0——9键即可查看10组时间值 #include reg52.hvoid display(unsigned char time[]);void display0(unsigned char data0[]);void display1(unsigned char data1[]);void display2(unsigned char data2[]);void display3(unsigned char data3[]);void display4(unsigned char data4[]);void display5(unsigned char data5[]);void display6(unsigned char data6[]);void display7(unsigned char data7[]);void display8(unsigned char data8[]);void display9(unsigned char data9[]);void key(void);unsigned char code seg[13]={0x3f, 0x06, 0x5b, 0x4f, 0x66, 0x6d, 0x7d, 0x07, 0x7f, 0x6f,0x77, 0x7c, 0x39}; unsigned char code sel[4]={0x10,0x20,0x40,0x80};unsigned char time[4]={0,0,0,0};unsigned char data1[4]={0,0,0,0},data2[4]={0,0,0,0},data3[4]={0,0,0,0},?????????????? data4[4]={0,0,0,0},data5[4]={0,0,0,0},data6[4]={0,0,0,0},????? data7[4]={0,0,0,0},data0[4]={0,0,0,0},data8[4]={0,0,0,0},????? data9[4]={0,0,0,0};unsigned char count;unsigned char keytmp;unsigned char begin=0; void timeinit(void) interrupt 1{ count=1;TH0=0xd8;TL0=0xf0;} void main(void){unsigned char a,b,c,d,i;count=0;TMOD=0x01;TH0=0xd8;??? TL0=0xf0;ET0=1;TR0=1;EA=1; while(1){??? P1 = 0xfe;keytmp = P1;??? if(keytmp==0xf6) ??? { ?? begin=1;?? a=0;?? b=0;?? c=0;?? d=0;}while(P1==0xf6);if(begin==1){????? if(count==1) {a++;count=0;}?? if(a==10) {b++;a=0;}?? if(b==10) {c++;b=0;}?? if(c==10) {d++;c=0;}?? time[0]=a;?? time[1]=b;?? time[2]=c;?? time[3]=d;?? display(time);}P1 = 0xfe;keytmp = P1;switch(keytmp){????? case 0xee: {data7[0]=a;data7[1]=b;data7[2]=c;data7[3]=d;}while(P1==0xee);?????? break; ??? case 0xde: {data4[0]=a;data4[1]=b;data4[2]=c;data4[3]=d;}while(P1==0xde);???????? break;??? case 0xbe: {data1[0]=a;data1[1]=b;data1[2]=c;data1[3]=d;}while