- 1、本文档共6页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
应用EP+ID代替胶片法对MLC的质控研究.pdf
中华放射肿瘤学杂志2015年9月第24卷第5期 Chin J Radiat Oncol,September 2015,Vol.24,No.5 ·573 ·
·物理 ·生物 ·技术 ·
应用 EPID代替胶片法对 MLC 的质控研究
曹征 李红霞 鲍扬漪 洪德雄
【摘要】 目的 研究EPID代替胶片对加速器 MLC 的质控方法并探讨其在任意机架角度下的
可行性。 方法 采用RIT113软件对EPID影像和EBT3胶片影像数据进行分析。 以EBT3胶片射野
边缘50%等剂量曲线位置定义MLC叶片实际位置,在同一射野条件下EPID影像数据中找到MLC叶
片实际位置所对应百分剂量值,从而完成EPID到EBT3胶片的替代过程。 结果 加速器机架角0°
时,以EBT3胶片确定的MLC叶片位置处EPID影像对应的期望百分剂量值为44%,最大MLC位置
误差为012 mm。 任意机架角度时,EPID影像数据通过与0°结果做距离一致性分析比对,半径为
05 mm时所有像素点均通过。 结论 采用EPID代替胶片对加速器MLC叶片到位质控方法可行,且
其精度满足临床要求并适用于任意机架角的测量,具有广泛推广和借鉴意义。
【关键词】 电子射野影像装置; 放射自显影胶片; 多叶准直器; 质量控制; 模体
The study of electronic portal imaging devices for the position accuracy of multi⁃leaf collimator
∗ ∗
instead of the film Cao Zheng ,Li Hongxia,Bao Yangyi,Hong Dexiong. Radiotherapy Centre of
Department of Hematology and Oncology,First People′s Hospital of Hefei,Hefei230001,China
Corresponding author:Hong Dexiong,Email:hdx@mail.ustc.edu.cn
【Abstract】 Objective To exploretheapplicationof theelectronicportal imagingdevice (EPID)to
test on MLC leaves position accuracy instead of EBT3 film,and the feasibility analysis under any gantry
angle. Methods RIT113 softwarewasusedto analyzethe image data of radiochromicfilm EBT3 and EPID
of Siemens ARTISTE accelerator. The replacement processfrom EBT3film to EPIDfor the test MLC leaves
positioning was completed by defining the positions of 50% isodose curve of the field edge of EBT3 after
radiation astheactualpositionsof MLCleaves,thereforefindingoutthepercentageisodosevalueofthesame
position in the EPID portal imaging from the corresponding radiation field. Results When the accelerator
gantry anglewas0,the mean percentage isodose valuewas44% at the MLCleaves positions determined by
EBT3,and the maximum position error of MLC leaves is 012 mm. When the accelerator gantry was any
文档评论(0)