《冲压模具-花盘倒装式复合式冲裁模-冲压模具-说明书》.docVIP

花盘倒装式复合冲裁模学 生：马 骁 指导老师：周光永 湖南农业大学东方科技学院，长沙 410128 摘 要：采用弹压卸料的方式，弹压卸料具有结构简单，卸料效果好，等优点，适合任务所需冲裁模。冲孔废料采用自由掉落的方式，在凸凹模的下方开口，使冲裁废料自然掉出。工件从凸模与凹模之间卸料，采用弹簧卸料板，不但可以起到冲裁压边的作用，还可以工件卸料。落料后的条料也采用弹簧卸料板卸料，从凸凹模中卸出。 关键词：冲裁；冲裁模；弹簧；CAD；卸料； The faceplate upside-down compound blandingdie Student: Ma Xiao Tutor: Zhou Guangyong Orient Science＆Technology College , Hunan Agricultural University, Changsha 410128, China Abstract: adopting the method of leaned uploading, which has the advantage with simple structure and good effect of uploading and adjust to blankingdie. Punching waste take the method of free drop out to make the blanking waste drop out in a natural way at the down open of concave-convex pattern.The product unload between the punch pin and the blanking cavity die unloading, straight by a spring stripper plate, not only can play the role of press edge, still can upload the product.After dropping material strip material also use spring stripper plate unloading, discharged from concavo-convex models Key words:blanding;blandingdie;spring;CAD;unload目 录摘要……………………………………………………………………………………1关键词…………………………………………………………………………………11前言…………………………………………………………………………………12设计任务……………………………………………………………………………22.1设计任务书 …………………………………………………………………22.2设计任务…………………………………………………………………3 3 工艺方案的确定……………………………………………………………………33.1零件的工艺分析……………………………………………………………33.2 制定冲压工艺方案…………………………………………………………3 4 冲压工件的有关计算………………………………………………………………44.1 排样方式的计算……………………………………………………………44.1.1 排样…………………………………………………………………44.1.2 搭边，条料宽度的计算…………………………………………44.2 压力中心的计算……………………………………………………………64.3 冲裁工艺力的计算…………………………………………………………8 5 冲裁模设计中的有关计算…………………………………………………………105.1 冲裁间隙……………………………………………………………………105.2 冲裁模刃口尺寸……………………………………………………………105.2.1 落料模刃口尺寸的计算……………………………………………115.2.2 冲孔模刃口尺寸的计算……………………………………………13 6 模具结构设计………………………………………………………………………156.1模的结构尺寸………………………………………………………………156.1.1冲孔凸模…………………………………………………………156.1.2冲孔凹模……………………………………………………………166.1.3落料凸模……………………………………………………………166.1.4落料凹模……………………………………………………………186.2凹模周界与模架设计……………………