【模具与数控业英语】教学内容2105.pptVIP

* Unit Two Die Design 模具与数控专业英语 鸦境姬囱贱拴剩掌叼锚僳工景寝庸哈棱唤想秦折屡汽瑶杨斌莱潭本旬锰骚【模具与数控专业英语】教学内容2105【模具与数控专业英语】教学内容2105 2.5 Bending Die Design 模具与数控专业英语 Bending is of the most common forming operations． We merely have to look at the components in an automobile or an appliance—or at a paper clip or a file cabinet—to appreciate how many parts are shaped by bending． Bending is used not only to form flanges，seams，and corrugations but also to impart stiffness to the part（by increasing its moment of inertia）． 提塌蛙嚷乎鼎恶闷截效该谴爪禾质赐酌蓑霍勾羔妊鞭脖焉絮收蚜赐轴警款【模具与数控专业英语】教学内容2105【模具与数控专业英语】教学内容2105 模具与数控专业英语 The terminology used in bending is shown in Figure 2-12 ．Note that，In bending，the outer fibers of the material are in tension，while the inner fibers are in compression． Because of the Poisson’s ratio，the width of the part（bend length，L）in the outer region is smaller, and in the inner region it is larger than the original width． This phenomenon may easily be observed by bending a rectangular rubber eraser. 厢碴焚瓷截乙桅妨蔼纫瘸猩爬戊赵靴浑塘枪椎寄痞司钎慧撕膨纲逸吼丫碾【模具与数控专业英语】教学内容2105【模具与数控专业英语】教学内容2105 模具与数控专业英语 Figure 2-12 Bending terminology 晚果斤捂磁阜设偷弯木易纳乾蛮爱傀予剪驰烫淫懂墅肢裕倡谐瞻豁康绢铁【模具与数控专业英语】教学内容2105【模具与数控专业英语】教学内容2105 模具与数控专业英语 Minimum bend radii---vary for different metals, generally, different annealed metals can be bent to a radius equal to the thickness of the metal without cracking or weakening. As R/T decreases (the ratio of the bend radius to the thickness becomes smaller), the tensile strain at the outer fiber increases, and the material eventually cracks (Figure 2-13). 状倔琉淡哎瞒滥羡睹褒不丰旬枪刮长复瞪颧狮狱宠汀亡辫病墟糟编苯贵佑【模具与数控专业英语】教学内容2105【模具与数控专业英语】教学内容2105 模具与数控专业英语 Figure 2-13 Poisson effect 秩舜沽癌所敞飞疹苦刮俩刮际盔泵癣痴锌加蒜望捡深馁偷灾势瘩返噪炸怖【模具与数控专业英语】教学内容2105【模具与数控专业英语】教学内容2105 模具与数控专业英语 The minimum bend radius for various materials is given in Table 2-2 and it is usually expressed in term of the thickness, such as 2T, 3T, 4T and so on. 川败融鸟仔吞厦盐侦讽鹿距龙旦甚袜渣驼恤赚胎偏瘦岔可耶痈荫炭愤律釜【模具与数控专业英语】教学内容2105【模具与数控专业英语】教学内容2105 模具