大型圆柱孔圆柱滚子轴承游隙滚道直径公差滚子组直径公差和套圈滚道直径公差.docVIP

表1 0组游隙，滚子组直径公差和套圈滚道直径公差 mm 轴承公称内径d O组径向游隙(μm) 滚子公称直径Dw 内径带双档边的轴承 外圈带双档边的轴承 滚道直径 滚子组外径 滚道直径 滚子组内径 Di De Ew De di Fw 超过 到 Min Max 超过 到 公差 500 560 240 360 30 50 50 80 +0.030 -0.040 +0.310 +0.240 0 -0.050 +0.040 -0.030 -0.240 -0.310 +0.050 0 ?.035 0 ?.0353 560 630 260 380 30 50 50 80 +0.030 -0.040 +0.330 +0.260 0 -0.050 +0.040 -0.030 -0.260 -0.330 +0.050 0 ?.035 ?.035 630 710 285 425 30 50 50 80 +0.030 -0.050 +0.365 +0.285 0 -0.060 +0.050 -0.030 -0.285 -0.365 +0.060 0 +0.035 -0.045 +0.045 -0.035 710 800 310 470 30 50 50 80 +0.030 -0.050 +0.410 +0.310 0 -0.060 +0.050 -0.030 -0.310 -0.410 +0.060 0 +0.035 -0.045 +0.045 -0.035 800 900 350 520 30 50 50 80 +0.028 -0.063 +0.445 +0.350 0 -0.075 +0.063 -0.028 -0.350 -0.445 +0.075 0 +0.033 -0.058 +0.058 -0.033 900 1000 390 580 30 50 50 80 +0.028 -0.063 +0.505 +0. 390 0 -0.075 +0.063 -0.028 -0.390 -0.505 +0.075 0 +0.033 -0.058 +0.058 -0.033 1000 1120 430 640 50 80 +0.032 -0.072 +0.550 +0.430 0 -0.090 +0.072 -0.032 -0.430 -0.550 +0.090 0 1120 1250 470 710 50 80 +0.032 -0.072 +0.620 +0.470 0 -0.090 +0.072 -0.032 -0.470 -0.620 +0.090 0 1250 1400 530 790 50 80 +0.032 -0.092 +0.680 +0.530 0 -0.110 +0.092 -0.032 -0.530 -0.680 +0.110 0 1400 1600 610 890 50 80 +0.032 -0.092 +0.780 +0.610 0 -0.110 +0.092 -0.032 -0.610 -0.780 +0.110 0 表2 2组游隙，滚子组直径公差和套圈滚道直径公差 mm 轴承公称 内径 d 2组径向 游隙 (μm) 滚子公称 直径 Dw 内径带双档边的轴承 外圈带双档边的轴承 滚道直径 滚子组外径 滚道直径 滚子组内径 di De Ew De di Fw 超过 到 Min Max 超过 到 公差 500 560 120 240 30 50 50 80 +0.150 +0.080 +0.310 +0.240 +0.120 +0.070 -0.080 -0.150 -0.240 -0.310 -0.070 -0.120 +0.155 +0.085 -0.085 -0.155 560 630 140 260 30 50 50 80 +0.150 +0.080 +0.330 +0.260 +0.120 +0.070 -0.080 -0.150 -0.260 -0.330