6-PROEWìldfìre工程特征.pptVIP

Pro/ENGINEERwildfire 2.0 工程特征建立 大 綱 1﹑孔(Hole) * 2﹑殼(Shell) 3﹑肋(Rib) 4﹑拔模 (Draft) * 5﹑倒C角 (Chamfer) * 6﹑倒圓角(Round) * 1﹑關于孔特征 1.1﹑使用者界面(直孔) 1.1﹑使用者界面(標准孔) 1.2﹑孔位置放置參照 1.3﹑孔位置的放置類型 2﹑關于殼特征 2.1﹑使用者界面(殼) 2.2﹑Shell特征注意事項 2.3﹑范例﹕建立殼特征 2.4﹑范例﹕建立殼特征的順序 3﹑關于肋特征 3.1﹑使用者界面(肋) 3.2﹑草繪肋特征 3.3﹑定義肋特征 4﹑關于拔模 4.1﹑使用者界面(拔模) 4.2﹑建立拔模的一般步驟 4.3﹑關于分割拔模 4.4﹑范例1﹕建立基本拔模 4.5﹑范例2﹕建立草繪分割拔模 4.6﹑范例3﹕建立分割拔模 4.7﹑范例4﹕建立可變角度拔模 4.8﹑范例5﹕建立曲面分割拔模 5.1﹑倒圓角類型 5.2﹑倒圓角放置參照 5.3﹑圓角建立方式與截面形狀 5.4﹑范例1﹕建立恆定圓角 5.5﹑范例2﹕建立可變圓角 5.6﹑范例3﹕建立由曲線驅動的圓角 5.7﹑范例4﹕建立完圓倒角 6.1﹑倒C角類型與參照 6.2﹑倒C角尺寸的布置 6.3﹑范例1﹕建立倒C角 6.4﹑范例2﹕建立轉角倒角 6.5﹑倒C角練習﹕ Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 邊 邊鏈 曲面對邊 曲面對曲面 轉角倒角 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. * Pro/E-wildfire teaching material Page:* * Pro/E wildfire2.0 teaching material Date: 16-Dec-04 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. 注﹕以上標題中帶*號為重點掌握 Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pty Ltd. Evaluation only. Created with Aspose.Slides for .NET 3.5 Client Profile 5.2.0.0. Copyright 2004-2011 Aspose Pt