Rolqnd设备初始化参考.doc

Roland设备初始化参考 ???? ????几乎所有的MIDI设备都可以用简单的方法清除用户存储，回到出厂状态。以下资料是根据一位大侠Peter Ullrich几年前在因特网上的帖子编译的。?????????键盘合成器?????????A-JUNO: ?????????打开电源的状态下关闭（Off）内存保护开关（Memory Protect switch）。关闭电源，按住PORTAMENTO DATA TRANS二钮打开电源。?????????D-5(D):?????????按mode钮，直到进入ROM play模式。?????????按住EXIT EDIT二钮，按ENTER钮。?????????按住A/B，按BANK 7。?????????如果要退出，按住A/B，按EXIT。?????????D-10/20(D)?????????按住TUNE/FUNCTION WRITE打开电源。?????????[TUNE/FUNCTION] + [[WRITE]] :初始化D10/20到开箱状态?????????[[EXIT]] + [EDIT] :使D10/20进入检测模式?????????[EXIT] + [EDIT] :内存测试?????????[EXIT] + [TUNE/FUNCTION] :控制器测试，显示弯音值等?????????[EXIT] + [MIDI] :键盘测试，显示编号和力度?????????[EXIT] + [COMPARE] :D/A 调整和PCM检测. Band钮回放PCM声音，作D/A设置?????????[EXIT] + [ENTER] :指示灯检测，全部灯闪光?????????[EXIT] + [WRITE] :似乎瞬间使屏幕变暗?????????[EXIT] + [DATAXFER] :似乎瞬间使灯点亮?????????[EXIT] + [PERFORMANCE/MULTI-TIMBRAL] :(D20 only)软驱测试?????????D-70(D): ?????????按住BANK 8打开电源。按ENTER，再按WRITE。?????????JD-800:?????????按DATA TRANSFER钮。?????????使用up/down光标钮选择[FACTORY RESET]。?????????按YES。?????????JV-30: ?????????同时按下CHORUS REVERB，然后按VALUE up?????????JV-35 JV-50清除用户数据，恢复厂家设置: ?????????同时按[CONTROL] + [MASTER] ?????????按VALUE up ?????????JV-80清除用户数据，恢复厂家设置: ?????????关机 ?????????按住右下方[8]开机 ?????????屏幕显示 Initalize All Parameter message is dispayed 按[ENTER] ?????????再按[WRITE] ?????????进入JV-80测试模式：?????????同时按住[write] + [number 1] + [number 8]开机。?????????按[EXIT]退出测试模式。?????????JV-1000:?????????按住CAPS打开电源。按ENTER，再按WRITE。?????????JW-50: ?????????按TUNE/FUNC钮。?????????按[F5]厂家预置, [F4] JW复位, [F3] GS复位?????????按[F4] YES?????????JX-1:?????????按住WRITE FLUTE打开电源。?????????U-20:?????????没有厂家预置。?????????VK-1000:?????????按WRITE钮调出Write菜单。?????????按F3打开初始化菜单屏幕。?????????按F4进入冷启动屏幕。?????????按ENTER钮。?????????合成器模块?????????D-110(D):?????????按住WRITE/COPY ENTER打开电源。?????????D-550(D):?????????按住BANK 2 , NUMBER 6 ENTER打开电源?????????DS-330:?????????按住REVERB and SPLIT打开电源。????????