小便斗安装指引.doc

小便斗安装指引 小便斗安装指引提要：缷下小便斗,用保温胶水将橡胶密封圈粘牢在铜配件马头的密封平面,小便斗再次就位并调平、正直,紧固铜配件马头与小便斗连接的螺丝将小便斗固定; 源自物管手册 给排水管道安装 按图纸和小便斗尺寸要求,安装给水、排水管道。 .给水管道预留DN15内螺纹接口,要求预留口平批荡面; 2.排水管道预留∮50排水PVc管口,要求预留∮50弯口平批荡面、∮50管口凸批荡面50㎜; 3.给、排水管道用塞头封堵,试压、试水办理隐蔽验收。 交建筑进行批荡、贴饰面砖。 安装前准备 将小便斗其中一套的配件马头,用钢锯按图所示对马头进行锯割加工,作为PVc排水管丝攻备用。 小便斗安装 .挂小便斗支架安装--按图纸和小便斗尺寸要求定位打孔,用∮8㎜胶塞、4×40㎜自攻螺丝安装挂支架; 2.将预留∮50排水PVc排水管口锯平饰面砖,并用水泥膏将管口外壁与填平; 3.用加工好的铜配件马头丝攻,::对∮50PVc管内壁进行攻丝,要求PVc管的内螺纹长度30㎜为宜; 4.安装铜配件马头,进行小便斗试装,要求小便斗的排水口与铜配件马头孔同轴;如有上下偏差可采用黑铅垫片调整,使小便斗的排水口与铜配件马头孔同轴; 5.缷下小便斗,用保温胶水将橡胶密封圈粘牢在铜配件马头的密封平面,小便斗再次就位并调平、正直,紧固铜配件马头与小便斗连接的螺丝将小便斗固定; 给水附件安装 、安装给水DN15电磁阀和DN15连接软管、安装电池; 2、进行通水试验,检查给排水,确认无渗漏现象;沿四边打玻璃胶填缝,小便斗安装完成。 源自物管手册 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct world outlook, outlook on life, values, to cultivate students unity and mutual assistance, honest and trustworthy, law-abiding, good quality, hard work, set a good XX students ideological quality, psychological quality and image quality. The formation of excellent moral education curriculum system and manage