木门窗施工工艺流程_0.docVIP

木门窗施工工艺流程 木门窗施工工艺流程提要：然后按设计门窗贴脸宽度及门口宽度锯切大芯板,用圆钉固定在墙面及门洞口,圆钉要钉在木模子上。检查底层垫板牢固安全后,可做防火阻燃涂料涂刷处理 房地产E网 木门窗施工工艺流程 1.施工内容 木门窗主要可分为平开门窗及推拉门窗两大类。 对原门窗的改造主要有以下三种方式: 第一是对原门窗进行更换,拆去原门窗,定购或现场制作新门。 第二种是原门、框不动,进行装修改造,在原门扇上加贴优质饰面材料并做装饰造型,原框保留加包门套及门口。 第三种方法是加门窗,即在无门的空间加作新隔断门,在原窗不动的条件下在内侧加装饰性强的窗户,以提高密封性。 2.施工工艺 （1）平开木门窗:安装平开木门窗的安装程序如下: 确定安装位置→弹出安装位置线→将门窗框就位,摆正→临时固定→用线坠、水平尺将门窗框校正、找直→将门窗框固定于→预埋在墙内→将门窗扇靠在框上→按门口划出高低、宽窄尺寸后刨修合页槽→位置应准确。 （2）悬挂式推拉木门窗的安装程序如下: 确定安装位置→固定门的顶部→侧框板固定→吊挂件套在工字钢滑轨上→工字钢滑轨固定→固定下导轨→装入门扇上冒头顶上的专用孔内→把门顺下导轨垫平→悬挂螺栓与挂件固定→检查门边与侧框板吻合后→固定门→安装贴脸。 （3）下承式推拉窗的安装程序如下: 确定安装位置→下框板固定→侧框板固定→上框板固定→剔修出与钢皮厚度相等的木槽→钢皮滑槽粘在木槽内→专用轮盒粘在窗扇下端的预留孔里→将窗扇装上轨道→检查窗边与侧框板缝隙→调整→安上贴脸。 3.施工要点 在木门窗套施工中,首先应在基层墙面内打孔,下木模。木模上下间距小于300毫米,每行间距小于150毫米。 然后按设计门窗贴脸宽度及门口宽度锯切大芯板,用圆钉固定在墙面及门洞口,圆钉要钉在木模子上。检查底层垫板牢固安全后,可做防火阻燃涂料涂刷处理。 门窗套饰面板应选择图案花纹美观、表面平整的胶合板,胶合板的树种应符合设计要求。 裁切饰面板时,应先按门洞口及贴脸宽度弹出裁切线,用锋利裁刀裁开,对缝处刨45°角,背面刷乳胶液后贴于底板上,表层用射钉枪钉入无帽直钉加固。 门洞口及墙面接口处的接缝要求平直,45°角对缝。饰面板粘贴安装后用木角线封边收口,角线横竖接口处刨45°角接缝处理。 房地产E网 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal