模板工程施工方案（十）.docVIP

模板工程施工方案（十） 模板工程施工方案（十）提要：框架柱模施工工艺柱模板：面板采用多层夹板，背肋用50×100mm木方或Φ48钢管，围檩用钢管 更多建筑学堂 模板工程施工方案（十） 1、承台基础模板施工 本工程设计为桩基柱下独立承台，承台厚度主要约为1200mm，根据工程特点以及土方开挖特点，选用240mm砖胎模作为承台基础及地梁的模板，砖胎模采用标准粘土砖m5水泥砂浆砌筑，砌筑前砖应按规定要求浇水湿润，砌筑时应按《砌体工程施工质量验收规范》（GB50203-2002）的要求控制砌筑质量，灰缝应饱满并横平竖直，内侧抹一层1∶水泥砂浆。 2、框架柱模施工工艺 柱模板：面板采用多层夹板，背肋用50×100mm木方或Φ48钢管，围檩用钢管。背肋的间距为300mm，围檩的间距为500mm。考虑到矩形柱尺寸较大，泵送砼坍落度大，柱面宽800-1000mm者，截面中间加一根Φ12＠500拉紧螺栓。 3、墙模板支模 面板采用多层夹板，背肋用50×100木料，间距300mm，钢管支撑，散支散拆。采用Φ16穿墙螺栓对拉，间距600mm，外墙的穿墙螺杆用止水螺栓。 4、框架梁板模板支模 梁板模板：面板采用多层夹板，背肋采用50×100木料，模板支撑采用早拆体系（示意图如下）。 梁板模板支撑体系采用脚手钢管（φ48×）搭设满堂脚手架，断面尺寸不大于300×700mm梁的梁底钢管纵横向间距按经验控制在－，离地300mm设第一道水平牵杆，其余水平牵杆间距不在于，再按规范要求设置水平、竖向构造剪力撑以增强使脚手架的整体稳定性。断面尺寸大于400×800mm梁应编制专题施工方案，其模板支撑架应进行验算。 5、底模拆除时的砼强度要求 现浇结构的模板及其支架拆除时，砼强度应符合设计要求及符合拆模时所需砼强度。 侧模在砼强度能保证其表面及棱角不因拆除模板而受损坏时，方可拆除。 模板拆除，应先松螺栓，拆除柱、梁侧模，不得强行硬撬，更不得碰撞梁的顶撑；当拆除梁底模时，必须满足拆模时所需砼强度要求，并得到工地技术负责人同意拆模，方可进行，拆模时不得野蛮行事，严禁硬撬、冲击砼构件。必须保证拆一处清一处，不留边角配件，保持搂梯、通道畅通。 Measures for the routine management of moral education in Middle SchoolsMethod of conventional management of moral education in middle schoolFirst, the guiding ideology:School moral education is an organic whole of the whole education work, always adhere to the school adhere to the moral education, education for this product, and actively promote the quality education, the school building efficient curriculum system of moral education, moral education, improve the sense of attraction and appeal, enhance the moral education work for through and timeliness. Teach everyone, service education and management education, and school moral education work must be with family education and community education closely together, to form a concerted pattern, and strive to create a good atmosphere for education, and to promote the all-round development of students, to establish a scientific moral education full of vigor the For long-term mechanism.Two, the goal of moral education:To guide the students to form the correct wor