信号发生器程序.doc

#includereg52.h //包含头文件 #includeintrins.h #define uchar unsigned char //宏定义 #define uint unsigned int sbit s1=P3^4; //定义按键的接口 sbit s2=P3^5; sbit s3=P3^6; sbit s4=P3^7; sbit lcdrs=P2^3; //液晶控制位 sbit lcdrw=P2^4; sbit lcden=P2^5; char num,boxing,u; //定义全局变量 int pinlv=100,bujin=1,bujin1=1; uchar code table[]=0123456789; //定义显示的数组 uchar code table1[]=frequence:boxing:; unsigned long int m; int a,b,h,num1; uchar code sin[64]={ 135,145,158,167,176,188,199,209,218,226,234,240,245,249,252,254,254,253,251,247,243,237,230,222,213,204,193,182,170,158, 146,133,121,108,96,84,72,61,50,41,32,24,17,11,7,3,1,0,0,2,5,9,14,20,28,36,45,55,66,78,90,102,114,128 }; //正弦波取码 uchar code juxing[64]={ 255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255, 255,255,255,255,255,255,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0 }; //矩形波取码 uchar code sanjiao[64]={ 0,8,16,24,32,40,48,56,64,72,80,88,96,104,112,120,128,136,144,152,160,168,176,184,192,200,208,216,224,232,240,248, 248,240,232,224,216,208,200,192,184,176,168,160,152,144,136,128,120,112,104,96,88,80,72,64,56,48,40,32,24,16,8,0 }; //三角波取码 uchar code juchi[64]={ 0,4,8,12,16,20,24,28,32,36,40,45,49,53,57,61,65,69,73,77,81,85,89,93,97,101,105,109,113,117,121,125,130,134,138,142, 146,150,154,158,162,166,170,174,178,182,186,190,194,198,202,206,210,215,219,223,227,231,235,239,243,247,251,255 }; //锯齿波取码 void delay(uint xms) //延时函数 { int a,b; for(a=xms;a0;a--) for(b=110;b0;b--); } void write_com(uchar com) //写命令函数 { lcdrs=0; lcdrw=0; lcden=0; P0=com; delay(1); lcden=1; delay(1); lcden=0; } void write_date(uchar date) //写数据函数 { lcdrs=1; lcdrw=0; lcden=0; P0=date; delay(1); lcden=1; delay(1); lcden=0; } void init_lcd() //初始化函数 { //lcden=0; //默认开始状态为关使能端，见时序图 write_com(0x0f); write_com(0x38); //显示模式设置，默认为0x38,不用变。 write_com(0x01); //显示清屏，将上次的内容清除，默认为0