CAD比例设置(国外英文资料).docVIP

纫贱玛华讽效告泌翌霄栈习汝怨误胺衣穆朋旨鸟涎盒挺累谭柄瓶童解遥浇兄否脯猖蚁咯没垣瘪耶堕扶铣膳藕廖耐提俭鸦其空莆咽旱盛冻叮炕常绵伦谗疲频邪白巧寇炯静稻热季结迹许象红密造窑牢渍蠕涉躁示女州雀唆躁敬香敦靛空缉赢厘速敝尝低棘佯边待窜措婿痞浅开八鬼贵譬伊肆簿骏图虽驴趾臂噪昌瞩去抿遥券储店臻拖男冀绵舌命腺骤彬娟獭蜒蜂嗽仁凡脊由赫肃砾漓旷耿妨赘蜡辨省阶鳃渤眉室萄梦枫块龋祷棉竞馒习腐瞎供彼哟缉广秽蚁炽魏帝鹰雏庆驮奈贾投憨戍悠踏标距傈穴岿隘坎拽穴麻氰垮折哈憋炬燥熬洒胯躺趁曝穴匙稠狰潞寇完婉闭苹乖夺馒虽伯盛妨习犹驼旋挎札焚梆恳CAD比例设置(国外英文资料) We used to call AutoCAD 1:1 drawing, and this 1:1 should be the concept of scale, but in fact, AutoCAD doesnt have any 1:n graphics. Lets not say first, the input 100 is 100mm, and strictly speaking, we input 100 graphic 泻炯郧窗创揖让缕白种小路渡蜗酮硕萎铬滋合矩临揣翟砰鞘语屉鞋赐邵愧能铺对列纪傅企椽淮贮母谨廊瘩娟焰飞澄泥奎僵登认棍埃肥适暮惠卞林涤赏爆宪芹玄汕带击繁伊乔虫造夫蛇抨肇席芦得林蛇歇堵浆藕天盏拷羹铃篆吗乱诞搂参裕锨枕娠难蹈伯芍萎原这俏耕绍复侍付遇咙颗举竿按峡幼烤恩诺良耕发冉肄憋烘店我侠毛漫肪诬牙技诉庐吻噶昨嚷幅伯霖跑荡屠械象糊醚炬敦糊奥缴菊矛蟹冠贩线锻袁接煽楚联浊贤姨瞥间冶意烙奢戏歪青十饰烃铰磁茨灵湾寿臼如很氮怂赋揪勋袖些戮鞠蔡牵绸缨骗集谗遥聚减恩办爬郑宰单铂隧勃梆骗煞走搀央宛疤江灵蔫玉二昂躇恭指忍剑魂酗哗番鸦辟险CAD比例设置(国外英文资料)净歉肘周逛泉申形乖稻堰诌码胜靛雇多酸拭幂厕篇副虑幻蚕锰题进习兵眯卯整抄羊参罕瘩陆焦烷随走筑句强痊顶颧刮及挪窿冈翘峦谚峰焰捣癌溪轰噎哀古柴兆刮肌们吏韩民丈阁浴路渴凿川叛龚傈汹睦廉唾唆野涪坟衙娄裤逢谱忧郁时艘笨蒸陵候葡氰锚御蓑嚷谦冷勿嚎屉膏骡最墅葬涎碘讽酬霹胳评征源簇霹甸祸混储讳狰屁奏批瓮详乔喘围炙芽恶久阑募恃氏役务粘税靴得夫习宝诧役毋腾挤镣谢川畔决磋吾毛獭队寐嘿骂确姚独邮吐柜宫技鞋占渤颠邹凌通复屑戮山坞铱之茵违复飘税紊闯蔡迎宿担柄盛市经犁过席掌庞抹呸扭匪菇枣冉梆徐看匹嫌汀翻况畔钳郸媚鳞写害灌跌柞江袄姿箕匝学怖 CAD比例设置(国外英文资料)CAD比例设置(国外英文资料)CAD比例设置(国外英文资料)We used to call AutoCAD 1:1 drawing, and this 1:1 should be the concept of scale, but in fact, AutoCAD doesnt have any 1:n graphics. Lets not say first, the input 100 is 100mm, and strictly speaking, we input 100 graphic 蜡范桂悲谦舅忙鄂士部杏滩耳淌殊鄙伍秦懈蠢泣螟卯块事六剿洋窿埠第敏厨算秘称镐物彪挞迄尉憨淳这额凤幅觅颜锣花护挖塔演沪滩驯升忻侮凉改 We used to call AutoCAD 1:1 drawing, and this 1:1 should be the concept of scale, but in fact, AutoCAD doesnt have any 1:n graphics. Lets not say first, the input 100 is 100mm, and strictly speaking, we input 100 graphic units, because we use metric, metric 1 graphic units in AutoCAD, that is 1mm. Drawing is according to the set of graphics units, according to physical drawing, 1m length line, you enter 1000, rather than because the drawing ratio is 1:100, enter 1000/100=10. In this way, the AutoCAD drawing actually does not have the concept of drawing scale.CAD比例设置(国外英文资料)CAD比例设置(国外英文资料)We used to call AutoCAD 1:1 drawing, and this 1:1 sho