跨交换机的VLAN配置实验.docVIP

vlan database这条命令cisco已经不推荐使用这个命令了，现在要创建vlan的话直接在conf t下打vlan就OK了 添加VLANSW1#vlan databaseSW1(vlan)#vlan 10 VLAN 10 added:??? Name: VLAN0010SW1(vlan)#vlan 20VLAN 20 added:??? Name: VLAN0020SW1(vlan)#vlan 30VLAN 30 added:牋?Name: VLAN0030SW1(vlan)#vlan 40VLAN 40 added:牋?Name: VLAN0040SW1(vlan)#vlan 50VLAN 50 added:牋?Name: VLAN0050SW1(vlan)#exitAPPLY completed.Exiting....SW1#show vlan-sw brief VLAN Name牋牋牋牋牋牋牋牋牋牋牋牋牋牋 Status牋?Ports---- -------------------------------- --------- -------------------------------1牋?default牋牋牋牋牋牋?牋牋牋牋牋牋 active牋?Fa0/0, Fa0/1, Fa0/2, Fa0/3牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋?Fa0/4, Fa0/5, Fa0/6, Fa0/7牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋?Fa0/8, Fa0/9, Fa0/10, Fa0/11牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋牋?Fa0/12, Fa0/13, Fa0/14, Fa0/1510牋 VLAN0010牋牋牋牋牋牋牋牋牋牋牋牋 active牋?20牋 VLAN0020牋牋牋牋牋牋牋牋牋牋牋牋 active牋?30牋 VLAN0030牋牋牋牋牋牋牋牋牋牋牋牋 active牋?40牋 VLAN0040牋牋牋牋牋牋牋牋牋牋牋牋 active牋?50牋 VLAN0050牋牋牋牋牋牋牋牋牋牋牋牋 active牋?1002 fddi-default牋牋牋牋牋牋牋牋牋牋 active牋?1003 token-ring-default牋牋牋牋牋牋牋 active牋?1004 fddinet-default牋牋牋牋牋牋牋牋?active牋?1005 trnet-default??????????????????? active设置中继并配置以太通道捆绑 SW1#conf tEnter configuration commands, one per line.? End with CNTL/Z.SW1(config)#interface range fastethernet0/1 - 4SW1(config-if-range)#switchport mode trunk*Mar? 1 01:12:29.463: %DTP-5-TRUNKPORTON: Port Fa0/1-4 has become dot1q trunkSW1(config-if-range)#switchport trunk encapsulation dot1qSW1(config-if-range)#channel-group 1 mode onCreating a port-channel interface Port-channel1 SW1(config-if-range)#*Mar?1 01:12:45.775: %EC-5-BUNDLE: Interface Fa0/1 joined port-channel Po1*Mar?1 01:12:45.991: %EC-5-BUNDLE: Interface Fa0/2 joined port-channel Po1*Mar?1 01:12:46.159: %EC-5-BUNDLE: Interface Fa0/3 joined port-channel Po1*Mar?1 01:12:46.339: %EC-5-BUNDLE: Interface Fa0