技术要求需要写的那些东西（The technical requirements that you need to write）.docVIP

下载本文档

7
0
约3.98万字
约 11页
2017-07-15 发布于河南
举报
版权申诉

技术要求需要写的那些东西（The technical requirements that you need to write）.doc

1、本文档共11页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

技术要求需要写的那些东西（The technical requirements that you need to write）

技术要求需要写的那些东西（The technical requirements that you need to write） 1. Remove the oxide skin from parts. 2. Defects on the surface of parts, such as scratch and abrasion, etc. Remove the burrs. 4. After adjustment, HRC50 ~ 55. 5. Parts for high frequency quenching, 350 ~ 370 ℃ tempering, HRC40 ~ 45. 6. Carburizing depth of 0.3mm. 7. High temperature aging treatment. 8. The non-shape tolerance should meet the requirements of gb1184-80. 9. The length of the unfilled length shall be allowed to be over 0.5mm. The casting tolerance band is symmetrical in the basic dimensions of the blank casting. 11. Unfilled radius R5. 12. Note chamfer are not 2 x 45 °. The acute Angle is blunt. 14. Oil must be soaked before assembly. 15. Assembly of hot charging rolling bearings allow used engine oil heating, oil temperature shall not exceed 100 ℃. 20. After the gear assembly, the contact spots and side gaps of the tooth surface should meet the requirements of GB10095 and GB11365. 21. When assembling hydraulic systems, seal packing or sealant is allowed, but should be prevented from entering the system. 22. The parts and parts (including external parts and external components) of the assembly shall be equipped with the qualification certificate of the inspection department. 23. The parts must be cleaned and cleaned before assembly, with no burrs, flying edges, oxidized skin, rust, cuttings, grease, colorants and dust. 24. The main mating dimensions of the components before assembly shall be carried out, especially the size and relevant accuracy of the oversize. The parts in the assembly are not allowed to knock, touch, scratch and rust. 26. When fastening screws, bolts and nuts, it is strictly prohibited to strike or use improper tools and wrenches. After fastening screw groove, nut and screw, bolt head shall not be damaged. 27. To tighten the fasteners required for tightening torque, torque wrenches must be adopted, and tightening torque should be tightened as required. When the same par