贴片机常见故障及解决方法.docxVIP

贴片机常见故障及解决方法1、PCB传输故障：① E0070：PCB TRANSFER ERROR Unexpected PCB is on the Conveyor PCB传输故障，额外的PCB在运输轨上意义：在运输轨上的PCB，数量超过额定的数量。② E0071：The PCB detected before transfer is not detected after transfer. Maybe there is the PCB on the edge of the moving conveyor . Set the PCB to its normal Position Manually. 传输前检测的PCB在传输后检测不到，可能在移动运输轨的边缘有PCB，用手将PCB放置在其正常的位置。意义：载入开始检测的PCB在载入后不能确认，卸出前确认的PCB在出口处检测不到，或载入卸出前不能确认的PCB 在载入卸出后被检测到。③ E0072：Machine in Unable to start running because the conveyor width is not ready . The conveyor width will be changed first . Misaligment of PUSH-UP PINS or PCB on conveyor may danage machine . Assure Safety and push the [ENTER] key. 意义：因未准备运输轨宽度机器不能开始运行，运输轨宽度将先被改变，在运输轨上的PCB或上推顶针的失调可能损坏机器，确保安全并按[ENTER]键。④ E0073：PCB is detected on the edge of the moving conveyor. Set the PCB to its normal Position mannally. 在移动运输轨边上检测到PCB，将PCB手动放置在正常位置。意义：在移动运输轨的的连接部分，危险警告传感器检测到一块PCB。⑤ E0074：PCB FIXING ERROR PCB trans-Unit, Locate-Pin or push-up-Unit does not response to command. PCB固定故障PCB传输部件，定位针或上推部件不响应指令。意义：在PCB传输部件上的定位针传感器或上推部件，传感器不能正确响应电磁阀的状况。⑥ E0078: When the PCB was transfered to fixed conveyor of PCB exit Side ,error happened for time over Maybe the PCB stoppered between fix conveyor and moving enveyor or the PCB stopped is fixed Conveyor of PCB exit side . Set the PCB to its normal position mannally.当PCB?传送到PCB出口处边的固定运输轨时，发生超时故障，PCB?可能停在固定运输轨和移动轨之间，或PCB停在PCB出口边的固定运输轨中，用手将PCB放在正常位置。?意义：当从运输轨上卸出PCB时，PCB不能到达出口传感器。?? ⑦?E0079:?The?PCB?was?not?able?to?exit?from?fixed?conveyor?of?PCB?exit?side?.?Maybe?the?PCB?stopped?on?edge?of?fixed?conveyor?of?PCB?exit?side.?Set?the?PCB?to?its?mormal?position?mannally.? ??????PCB不能从出口边的固定运输轨出来，PCB可能停在PCB出口边固定运输轨边上，手动将PCB放在正常位置。? ??意义：PCB不能载出到下一工序。?? ⑧?E0080：Moving?conveyor?can’t?net?move,?because?there?is?the?PCB?on?the?edge?of?the?moving?conveyor?.?Set?the?PCB?to?its?normal?position?mannally.? ??????移动运输轨不能移动，因为在移动运输轨边缘有PCB?，手动将PCB放于正确?位置。? 意义：工作台A和B之间有一块PCB?，阻碍工作台移动。?? ⑨?E0081：Fixed?conveyor?of?PCB?entrance?side?stopper?for?t