pcb飞针电测教程（PCB flying needle electrical measurement tutorial）.docVIP

下载本文档

64
0
约7.87千字
约 7页
2017-07-23 发布于河南
举报
版权申诉

pcb飞针电测教程（PCB flying needle electrical measurement tutorial）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

pcb飞针电测教程（PCB flying needle electrical measurement tutorial）

pcb飞针电测教程（PCB flying needle electrical measurement tutorial） 1, using this method to test files, often make a lot of test points, can not automatically delete the middle point. 2, the hole test is not good. View the generated connectivity (open) test points in ediapv, and there is no test point for individual holes. For example, there is a line on one side of the hole, and there is no line on the other side. According to reason, the hole should be tested on the other side without the line. However, the test points generated with the ediapv transformation are random, and sometimes the right ones are wrong. Depressed! 3 for REAR solder surface no window can be REAR layer name into other name, it ran out of a measuring point not to in EDIAPV. 4 if there is only one MEHOLE two windows, but both sides have run out of the measuring point, you can press it again to the make test programs button, note that the cursor in the top layer of MEHOLE. In this way, the welding points on the hole without the window can be removed. More than 5 of the names of the layers must not be wrong Oh, otherwise you will be in trouble later. Method two The first layer: import documents, inspection, order, etc. the two para, an outer line to change the name of the name was changed to fronrear. ily03 ily04neg, the inner layer is ily02, (if negative), rear, rearmneg Second: increase three layers, respectively, two welding layer and drilling layer copied to the increase of three layers, and change the name for fronmneg, rearmneg, mehole., met05-06, blind hole can be named met01-02., met02-05, and so on. Third: will affect the network of LINE or other things to delete, and then welding layer of PAD corresponding to the line layer into PAD, Fourth, combine the negative and positive slices and preserve the positive ones. The hole attribute of the MEHOLE layer is changed to PAD. After each layer is edited, the output of each layer is output in GENESIS OK, Fifth, fron, ily02, ily03, ily04neg, ilyo5neg,