upvc双壁波纹管安装工艺（Installation process of UPVC double wall corrugated pipe）.docVIP

下载本文档

6
0
约1.54万字
约 14页
2017-07-23 发布于河南
举报
版权申诉

upvc双壁波纹管安装工艺（Installation process of UPVC double wall corrugated pipe）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

upvc双壁波纹管安装工艺（Installation process of UPVC double wall corrugated pipe）

upvc双壁波纹管安装工艺（Installation process of UPVC double wall corrugated pipe） Manual construction and installation of double wall corrugated pipe project 1 General Provisions 1.0.1 in order to make the double wall bellows in the pipeline construction process to achieve safe and reliable, and ensure the quality of the project, the preparation of this manual. This manual applies to 1.0.2 hard polyvinyl chloride (PVC-U) and high density polyethylene (HDPE) double wall corrugated pipe, PVC-U pipe diameter dn200~500mm, HDPE pipe diameter dn400~800mm. pipe ring stiffness rating of S1 = 4KN/m2 and S2 = 8KN/m2 1.0.3 this manual is applicable to outdoor drainage and irrigation works in earthquake areas and non earthquake areas, and the outdoor drainage works in factories and enterprises can be referred to. 1.0.4 if any problems or special requirements are not dealt with in this manual, they shall be dealt with separately by the design unit. 1.0.5 according to this manual for double wall bellows construction, should comply with the states existing specifications, industry standards and the relevant provisions of the region, the relevant provisions of the procedures. 2 pipe General provisions of 2 and 1 2.1.1 pipe, rubber ring and other materials specifications should comply with the design requirements, with the quality inspection department of product certification and product performance manual, and should indicate product specifications and production date. 2.1.2 socket type sealing rubber ring is made of chloroprene rubber, and the shore hardness is 45-55MPa. It is supplied by pipe manufacturer according to specifications. 2 and 2 pipe quality 2.2.1 pipes require the same appearance, smooth inner wall, no cracks in the pipe body, and the pipe mouth shall not be damaged, split or deformed. The end face of 2.2.2 pipe should be smooth, vertical to the center axis of the pipe, and no obvious bending occurs in the axial direction. The dimension and roundness of the outer diameter an