回转支承的设计计算（Design calculation of slewing bearing）.doc

下载文档 降价啦

15
0
约8.72千字
约 14页
2017-07-24 发布于河南
举报
版权申诉
保障服务

回转支承的设计计算（Design calculation of slewing bearing）.doc

1、本文档共14页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。

回转支承的设计计算（Design calculation of slewing bearing）

回转支承的设计计算（Design calculation of slewing bearing） Design report of involute cylindrical gear drive Design information Designer Name= Zhu Jiacheng Design unit Comp= HeFei University of Technology Design date Date=2010-11-18 Design time Time=11:49:58 Two, design parameters Transfer power P=7.50 (kW) Transmission torque T=49.05 (N = m) Gear 1, speed n1=1460 (r/min) Gear 2, speed n2=199.66 (r/min) Transmission ratio i=7.3125 Prime mover load characteristic SF= slight vibration Working machine, load characteristic, WF=, uniform and stable Scheduled life H=10000 (hours) Three, layout and structure Structure form, ConS= closed type The gear 1 is arranged in a symmetrical arrangement of ConS1= The gear 2 is arranged in a symmetrical arrangement of ConS2= Four material and heat treatment Gear meshing type GFace= hardened surface Quality grade of heat treatment Q=ML Gear 1 material and heat treatment Met1=45 surface quenching Gear 1 hardness range HBSP1=45 to 50 Gear 1 hardness HBS1=48 Gear 1 material category MetN1=0 Gear 1 ultimate stress class MetType1=11 Gear 2 material and heat treatment Met2=45 surface quenching Gear 2 hardness range HBSP2=45 to 50 Gear 2 hardness HBS2=48 Gear 2 material category MetN2=0 Gear 2 ultimate stress class MetType2=11 Five, gear accuracy Gear 1, group I, accuracy JD11=7 Gear 1, group II, accuracy JD12=7 Gear No. 1, group III, accuracy JD13=7 Gear 1 tooth thickness deviation JDU1=F Gear 1 tooth thickness deviation JDD1=L Gear 2, group I, accuracy JD21=7 Gear 2, group II, accuracy JD22=7 Gear No. 2, group III, accuracy JD23=7 Gear 2 tooth thickness deviation JDU2=F Gear 2 tooth thickness deviation JDD2=L Six, gear basic parameters Modulus (normal modulus) Mn=12 End face modulus Mt=12.00000 Helix angle, beta =0.000000 (degree) Base helix angle, beta b=0.0000000 (degree) Gear 1 teeth number Z1=16 Gear 1 modification factor X1=0.500 Gear 1 teeth wide B1=90 (mm) Gear 1 tooth width factor phi d1=0.469 Gear 2 teeth number Z2=117 Gear 2 modification f