液晶显示器高压板维修代换（Liquid crystal display, high voltage board, maintenance, substitution）.docVIP

下载本文档

2
0
约1.17万字
约 9页
2017-08-03 发布于河南
举报
版权申诉

液晶显示器高压板维修代换（Liquid crystal display, high voltage board, maintenance, substitution）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

液晶显示器高压板维修代换（Liquid crystal display, high voltage board, maintenance, substitution） Repair LCD high-pressure plate fault is a headache, especially the difficult fault or with less than the corresponding pressure plate when the first two big, but not as scrap or retreat, that no face, in fact, people are living, as long as any pressure plate installed, then it is universal. Do not know the parameters to buy high pressure plate, pressure plate to see so many interface lines, dizziness! Is actually very simple, first determine the positive and negative power line, a fuse is generally positive, negative pole is connected to the capacitor anode. Then determine the best way to determine the voltage, voltage of the capacitor is labeled at about 6V, if there is a 3.3V, if the capacitance superscript around 12V, so the input voltage it must be 5V, if it is 24V or above, there is a 12V, and so on, the standard capacitor volt number by two, close to a few volts is a few volts. Some people say then according to this, it still doesnt work, or just flashed out, is a lot of pressure plate is more than this, how does that do? Find out the control at the foot, foot is receiving a small transistor on the general is directly connected to a transistor. Up to the middle of a small capacitor should be easy to recognize, control foot is generally 3.3V and 5V, there are also individual is grounded, so we do not know the circumstances, try not to the ground, then followed by 3.3V 5V, if the input voltage and the control voltage is more than 3.3V is that can be directly combined. What about the excess feet? Let him be free. Leave him alone After the high-pressure plate is broken, the most common are the following faults: 1, lit immediately after the problem is mainly for high pressure plate black feedback circuit plays the role of lead, such as: high voltage feedback circuit protection, lead to problems resulting in no feedback voltage, the feedback current is too large, loose tube PIN and I