螺纹电镀前尺寸精度的控制（Control of dimensional accuracy before thread plating）.docVIP

下载本文档

12
0
约9.52千字
约 9页
2017-08-04 发布于河南
举报
版权申诉

螺纹电镀前尺寸精度的控制（Control of dimensional accuracy before thread plating）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

螺纹电镀前尺寸精度的控制（Control of dimensional accuracy before thread plating） Abstract: as the most important thread of mechanical fasteners, its surface is mostly made of plating to anticorrosion and decoration, and is the most common way of galvanized plating, electroplating control thread size is the fundamental guarantee after plating the qualified size, is also a big problem in many thread processing enterprises. This paper sums up and summarizes the methods for controlling the dimensional accuracy of the thread products before years of electroplating. Keywords: thread; electroplating; dimensional accuracy; control CLC number: TG 501.2, document mark code: A Many rod end joint bearing products are threaded structures. Most of them are electroplated and used for corrosion protection and decoration. How to guarantee the thread size after electroplating is a difficult problem in the production process. In the long process of production practice, some experience has been mastered in the dimension control of screw plating. Effect of 1 coating on geometrical parameters of screw thread Assuming that the coating thickness is uniformly distributed on the thread, the effect of the coating on the medium diameter of the thread is shown in Figure 1 Fig. 1 Effect of plating on the medium diameter of thread (external thread, take the commonly used tooth shape angle 60 degrees as an example), of which: D is the diameter of the thread before the plating; D1 is the thread diameter after plating; t is the coating thickness; D is the single diameter increment after the plating. Geometric relationship: After plating, the total diameter of the thread is increased to: D1-d=2 Delta d=4t That is to say, the increase in the diameter of the thread is 4 times the thickness of the coating. The same reason, after the internal thread plating, the diameter of the reduction is also 4 times the thickness of the coating. In fact, in the electroplating process, due to the parts of the prominent parts prone