TN-S TN-C-S TN-C TT IT等接地系统的区别（The differences between tn-s tn-c-s tn-c TT IT and other ground systems）.docVIP

下载本文档

28
0
约1.13万字
约 9页
2017-08-04 发布于河南
举报
版权申诉

TN-S TN-C-S TN-C TT IT等接地系统的区别（The differences between tn-s tn-c-s tn-c TT IT and other ground systems）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

TN-S TN-C-S TN-C TT IT等接地系统的区别（The differences between tn-s tn-c-s tn-c TT IT and other ground systems） Analysis of the grounding mode of low voltage power supply system 1. Engineering construction power supply system The basic power supply system of the construction electricity is (380V) three-phase three-phase system and (38/220v) three-phase four-wire system, but these nouns are not very strict. The international electrotechnical commission (IEC) has established a unified regulation, known as TT system, TN system, IT system. The TN system is divided into tn-c, tn-s, tn-c-s system. The following is a brief analysis of the various power supply systems mentioned above. (1) basic methods of engineering power supply According to the various protection modes and terms of IEC, the low voltage distribution system is divided into three types according to the grounding mode, namely TT, TN and IT system, which are described as follows. (1) TT mode is the protection system which refers to the direct grounding of the metal enclosure of the electrical equipment, which is called the protective earthing system, also known as TT system. The first symbol T denotes the direct grounding of the neutral point of the power system; The second symbol T indicates that the metal case of the load device and the normally uncharged metal parts are connected directly to the earth, but not to the system. 1) when the metal case of the electrical equipment is electrified (when the phase line touches the shell or the equipment is damaged by insulation), the danger of electric shock can be greatly reduced due to the grounding protection. However, the low voltage circuit breaker (automatic switch) may not be able to jump, causing the outer shell of the leakage device to be higher than the safety voltage, which is a dangerous voltage. 2) when the leakage current is less than one hour, even if there is a fuse, it may not be able to fuse, so the leakage protection device should be used for protection.