切断刀的正确安装与使用（The correct installation and use of cutting knives）.docVIP

下载本文档

17
0
约4.5千字
约 4页
2017-08-15 发布于河南
举报
版权申诉

切断刀的正确安装与使用（The correct installation and use of cutting knives）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

切断刀的正确安装与使用（The correct installation and use of cutting knives）

切断刀的正确安装与使用（The correct installation and use of cutting knives） The correct installation and use of cutting knives To: 0 Time: 2011-04-1007:58 author: G54 CNC network click: 0 Cutting knife installation using precautions Cutting knife is often used in the processing of a turning tool, there is much need to be aware of its installation and use, when using cemented carbide cutting operation, correct installation tool is very important. If the cutting edge and the contact position of the workpiece are not correct, the cutter may collapse or damage the workpiece, sometimes even damage the machine tool. Two of the most common problem is to cut off the tool is perpendicular to the workpiece or cutting edge relative to the workpiece installation too high or too low, the central axis of the knives service life, chip control, and whether it can keep vertical and smooth cut off will produce great influence, will also result in finish machining of parts in surface with convex and concave surface. If these problems are serious, the tool will fail. To ensure that the tool is perpendicular to the workpiece, the operator should comply with a simple installation procedure. 1. Carefully clean the lock area first and install the cutting tool on the hexagonal turret. Then use an indicator to measure the tool deviation on a stroke of 100mm. The deviation should not exceed 1mm. 2. One way to check whether the tool is perpendicular is to check the chip produced. If the cuttings produced by the workpiece are flowing to the side with long filaments, this may be improper installation of the tool. Another phenomenon is the cutting of premature wear at the rounded corners of the blades, suggesting that the blade is under more pressure than the other side. 3. Please follow the installation steps mentioned above if the quality of the parts of the cutting tool or the parts of the production is changed. Sometimes a slight collision of a knife can lead to deviations. Therefore, it is a good idea t