fortigate上面检查网络连通性的三个步骤（FortiGate three steps to check network connectivity above）.docVIP

下载本文档

6
0
约4.16千字
约 6页
2017-08-16 发布于河南
举报
版权申诉

fortigate上面检查网络连通性的三个步骤（FortiGate three steps to check network connectivity above）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

fortigate上面检查网络连通性的三个步骤（FortiGate three steps to check network connectivity above）

fortigate上面检查网络连通性的三个步骤（FortiGate three steps to check network connectivity above） 1, scope of application All FortiGate devices running in NAT or TP mode. 2, description This paper describes the three typical steps on FortiGate network connectivity check, the output information of these three steps is also very useful but also must submit tcket attachments for FortiGate technical support center. The network environment we assume is shown below: [PC1] portA [FortiGate] portB = = = = = = = [PC2] PC1 and PC2 are connected directly to FortiGates portA and portB ports, or across the router to FortiGates portA and portB ports, and the problem is that PC1 cannot connect to PC2. 3, solutions Note: on the FortiGate interface that uses the NP2 network processor, the network traffic is likely to be accelerated by the NP2 processor hardware, resulting in sniffer and debug flow output errors. Please use this to confirm whether you use FortiGate devices with NP2 interface 2 commands, if NP2 interface please refer to how to use the sniffer or debug flow function described disable hardware acceleration of NP2 function in NP2 network interface on FortiGate. In general, the troubleshooting process is as follows: Step 1: sniffer Step two: debug flow Step three: session list Step 1, sniffer You can let PC1 continue with Ping PC2 and confirm the following questions: The Ping request packet is received from the desired FortiGate network port; Check that the ARP request is correct and send it from the destination interface; Check that the Ping request packet is sent from the desired FortiGate; Check if the Ping response is received from the above outgoing interface; Check that the Ping response is correct, from the portA port of FortiGate to the PC1. Specific instructions are as follows: FGT#, diagnose, sniffer, packet, any, host, PC1, or, host, PC2, 4 perhaps FGT# diagnose sniffer packet any (host PC1 or host PC2) and ICMP 4 In the sniffer filter, you can increase the ARP protocol at t