焊接机常见故障)（The welding machine common fault)）.docVIP

下载本文档

4
0
约1.48万字
约 9页
2017-08-16 发布于河南
举报
版权申诉

焊接机常见故障)（The welding machine common fault)）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

焊接机常见故障)（The welding machine common fault)）

焊接机常见故障)（The welding machine common fault)） The welding machine common fault. Fault welding machine is relatively more, and failure is also more complex, often is a result of a variety of causes, or a cause may also cause some results. Some fault it also is very difficult, we first make a brief description of the accident will scratch. 3.1 scratch In the welding tube machine scratch has two main parts which, one is guiding mechanism, two extrusion welding mechanism. The guiding part guiding mechanism 3.1.1 scratch scratch generally occurred in both sides of the tube, if equipped with a guide sleeve guide mechanism adjustment is reasonable, the tube on the two surface will be friction scratch, scratch wound is characteristic of the relatively large, strong continuity. Mainly because the height of the guide sleeve is not correct, or on the guide roller shaft bearing damage control, not good tube, formed to produce friction and guide sleeve. In addition, when the guide roller deviates from the rolling center line is too large, the axis of the guide sleeve and the guide roller of the relative difference is too large, it will cause scratches on both sides of the tube. 3.1.2 extrusion welding mechanism caused by the extrusion roller scratch scratch, mainly occurred in the bottom of the tube, the reasons are as follows: (1) pass does not match the weld structure of extrusion two roller type, three stick and four roller, as long as the combination of the pass is not consistent, it is easy to cause the tube surface scratches two, roller structure is particularly prominent. There are many factors causing the pass does not match, the two roller structure as an example, such as bearing damage, roller axial movement; hole size; the two roller height difference; shaft bending and assembly and instability. (2) the height, bottom edges extrusion roll pass should be highly consistent with the rolling line. The height of the guide roller is composed of steel tube wall thickness deter