高压旋喷技术在沉桩引孔中的应用（Application of high pressure jet grouting technology in bored pile driving）.docVIP

下载本文档

3
0
约8.92千字
约 7页
2017-08-17 发布于河南
举报
版权申诉

高压旋喷技术在沉桩引孔中的应用（Application of high pressure jet grouting technology in bored pile driving）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

高压旋喷技术在沉桩引孔中的应用（Application of high pressure jet grouting technology in bored pile driving）

高压旋喷技术在沉桩引孔中的应用（Application of high pressure jet grouting technology in bored pile driving） Source: good foundation, author: admin time: 2010-03-23, this paper has been published in the national construction technology magazine 1 project overview The XX area is located on the east coast of the Fenhe River and belongs to the alluvial terrace terrace. Is mainly composed of Quaternary Holocene artificial accumulation, quaternary Holocene river alluvium (Q4al+pl) and the upper Pleistocene river alluvium (Q3al+pl), with artificial fill, silty clay, silt and sand. TISCOs 1 million 500 thousand ton stainless steel steelmaking project is located on this stratum. The foundation treatment is made up of 600 high strength prestressed concrete pipe pile, and the bearing stratum is seventh layers of dense middle sand layer. The soil conditions are as follows; 1—1 杂填土，松散； 1—2 素填土，松散； 2—1 粉土，中密-密实； 2—2 细砂，松散-稍密； 2 粉质粘土，软塑-可塑； 3—1 粉质粘土，可塑-软塑；3 粉土，中密-密实；4—1 中砂，中密；4—2 粉质粘土，软塑；4 粉土，中密-密实； 5—1 粉土，中密-密实； 5 细砂，中密-密实，标准贯入试验实测锤击数N为20.0-50.0击，平均值为35.4击，厚度0.60—5.20m； 6—1 粉质粘土，可塑； 6 粉土，中密-密实，标贯击数N为20.0-45.0击，平均值为31.4击，厚度1.00-10.60m；7—1 粉土，局部透镜体，密实；7—2 圆砾，局部透镜体，密实；7 中砂，标贯击数N为43.0-50.0击，平均值为48.4击，厚度5.00-11.9 0m, dense. The project was designed by CISDI, PHC pile end bearing and friction requirements, pile into the support layer (seventh layer of dense sand in more than 2.5D (d) is the diameter of the pile, with seventh layer depth), selection of 18m ~ 25m of different length of pile, the pile tip closed, use track driver, D80 diesel pile hammer. The main design of the PHCAB600a pile steelmaking plant a total of 3269, with a total length of 73216 meters. 05 years in January 18th started, completed in April 17th. Piling before the owners to test pile made? PHC pile construction work instructions?, stop hammer standard elevation and penetration of the double control principle of penetration for the last three ten hits each array array less than 40mm, and according to the design requirements of the