钳工基础知识(二)（Basic knowledge of locksmith (two)）.docVIP

下载本文档

4
0
约6.23千字
约 6页
2017-08-18 发布于河南
举报
版权申诉

钳工基础知识(二)（Basic knowledge of locksmith (two)）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

钳工基础知识(二)（Basic knowledge of locksmith (two)）

钳工基础知识(二)（Basic knowledge of locksmith (two)） Basic knowledge of fitter (two) (2009-11-26 14:14:59). Tags: university education culture and entertainment topics for the classification of emotional life: Learning Marking and matters needing attention First, the role of the line and kind The dashed line is based on the pattern size requirements, using the stylus tool draw machining parts of the contour line in the rough or semi-finished product (or processing limit) or as a method of operating a reference point, line. The accuracy of the scribing is usually 0.25 to 0.5mm. 1., the role of the line - that is, semifinished products or semi-finished products, why should be crossed? (1) draw the contour lines for the rough or semi-finished processing line and the basis, reference point or line is drawn by the correction mark or the installation of the workpiece. (2) in single or small batch production, with a dash to check the shape and size of the rough or semi-finished products, reasonable distribution of the machined surface of the margin, early detection of unqualified products, to avoid the follow-up processing time waste. (3) cutting off the material on the board, so that the material can be correctly discharged and the material can be reasonably used. Marking is a complex, detailed and important work. If the marking is wrong, it will result in the scrap of the machined part. Therefore, marking is directly related to the quality of the product. The requirements for marking are accurate size, correct position, clear lines and uniform eye opening. 2. types of marking (1) the plane mark, that is, after marking off a plane of the workpiece, can clearly indicate the machining limit, and it is similar to the plane drawing method. (2) the stereo marking is the counter of the plane scribing, which is crossed on the surface of each part of the workpiece (usually the surface perpendicular to each other), that is, in the long, wide and high three directions. Two, lineation tool