检查标准(毛坯房)（Inspection standard (roughcast room)）.docVIP

下载本文档

3
0
约2.08万字
约 16页
2017-09-01 发布于河南
举报
版权申诉

检查标准(毛坯房)（Inspection standard (roughcast room)）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

检查标准(毛坯房)（Inspection standard (roughcast room)）

检查标准(毛坯房)（Inspection standard (roughcast room)） The 1980 contribution by Pinocchio Doc document may at the WAP end of the browsing experience poor. Suggest you select TXT, or download the source file to the machine view. No leakage, the detail of excellence quality inspection standards of no leakage, the detail of excellence Civil engineering part A wall 1.1 check each face of not less than 3 points. The 2.3 surface is smooth and clean, with no obvious pattern, joint formation, no cracking, number of block fine, no peeling. The 2.2 wall roughness by 2m on foot, foot inspection, the smoothness of the allowable deviation is less than 3mm; 2.4 vertically, allowable deviation is less than 3mm, yin and yang angle Fang Zhengshun straight, allowable deviation is less than 3mm; 2.5, the reserved hole groove, pipeline position, proper size, wall openings, neat and straight; the 2.6 surface of the thin wall cracking and hollowing, after repairing the original wall should be kept with the same color, no repair marks. Two, the ceiling (height) sizes, yin and yang angle ceiling (floors), room size, room size, 2.1 based on the smoothness of the ceiling should be level, check points in each room of 4-6 points; 2.2 floor to ceiling each check point height difference is greater than 15mm in the room, room four corner wall leads to horizontal point inspection. The ceiling level allows the deviation less than 10mm. The 2.3 is the most negative deviation of not more than 20mm, the range is less than 20mm 2.4 sizes at both ends should be equal, the range is less than 20mm, and no more than 0.5% vertical length of 2.5 of all indoor corner must be straight, kitchen and bathroom between yin and yang angle error of not more than 3mm. Three, floor The 3.1 floor surface roughness, cement color, clean, no pollution, no cracking and hollowing, no rough surface, not sand. The 3.2 floor 2m on foot and the feeler to check the flatness deviation less than 4mm. The 3.3 baseboard smooth straight, hig