材料在扭转时力学性能测定实验（Test of mechanical properties of materials in torsion）.docVIP

下载本文档

1
0
约9.97千字
约 11页
2017-09-15 发布于河南
举报
版权申诉

材料在扭转时力学性能测定实验（Test of mechanical properties of materials in torsion）.doc

1、本文档共11页，可阅读全部内容。
2、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。
3、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
5、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
6、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
7、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
8、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

材料在扭转时力学性能测定实验（Test of mechanical properties of materials in torsion）

材料在扭转时力学性能测定实验（Test of mechanical properties of materials in torsion） Test of mechanical properties of materials in torsion In mechanical engineering, many driving parts work under torsion. Determination of mechanical properties of materials in torsion is of practical significance for the design, calculation and material selection of shafts. First, preview requirements 1. Derive the formula for measuring shear stress limit of low carbon steel:; 2. The principle and procedure of measuring shear modulus of low carbon steel G are briefly described. Two, the purpose of the experiment 1. Determine the shear modulus of G of low carbon steel and verify the formula of torsional deformation. 2. Determine the shear yield limit of low carbon steel and the shear strength limit of low carbon steel and cast iron. 3. Compare the torsion deformation and failure rules of low carbon steel and cast iron. Three 、 experimental equipment and sample 1. Torsion testing machine. 2 、 torsion measuring G instrument or torsion angle instrument. 3 、 vernier caliper. 4 sample. Torsion specimens are generally round sections (Figure 1). The distance between the A and B two sections of the l0 for the installation of the torque meter is called the gauge distance. Before the experiment, two longitudinal lines and two round circumferential lines were drawn on the surface of the low carbon steel sample, so as to observe the torsion deformation. Four 、 principle and method of experiment Both the torsional deformation formula and the shear modulus of elasticity, G, are required to accurately measure the torsion of the specimen Angle. The torsion angle is usually measured with a torsion angle instrument. The construction principle and installation diagram of the torsion angle instrument are shown in figure 2. Torsion angle instrument is mounted on the sample A, B two section, with positioning screws, at the same time by putting A at the top dial connection counter B connection, the pre displacement of the