手工计算钢筋公式（Manual calculation of reinforcement formula）.docVIP

下载本文档

3
0
约1.27万字
约 14页
2017-10-07 发布于河南
举报
版权申诉

手工计算钢筋公式（Manual calculation of reinforcement formula）.doc

1、原创力文档（book118）网站文档一经付费（服务费），不意味着购买了该文档的版权，仅供个人/单位学习、研究之用，不得用于商业用途，未经授权，严禁复制、发行、汇编、翻译或者网络传播等，侵权必究。。
2、本站所有内容均由合作方或网友上传，本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺！文档内容仅供研究参考，付费前请自行鉴别。如您付费，意味着您自己接受本站规则且自行承担风险，本站不退款、不进行额外附加服务；查看《如何避免下载的几个坑》。如果您已付费下载过本站文档，您可以点击这里二次下载。
3、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等，请点击“版权申诉”（推荐），也可以打举报电话：400-050-0827(电话支持时间：9:00-18:30)。
4、该文档为VIP文档，如果想要下载，成为VIP会员后，下载免费。
5、成为VIP后，下载本文档将扣除1次下载权益。下载后，不支持退款、换文档。如有疑问请联系我们。
6、成为VIP后，您将拥有八大权益，权益包括：VIP文档下载权益、阅读免打扰、文档格式转换、高级专利检索、专属身份标志、高级客服、多端互通、版权登记。
7、VIP文档为合作方或网友上传，每下载1次，网站将根据用户上传文档的质量评分、类型等，对文档贡献者给予高额补贴、流量扶持。如果你也想贡献VIP文档。上传文档

手工计算钢筋公式（Manual calculation of reinforcement formula）

手工计算钢筋公式（Manual calculation of reinforcement formula） Manual calculation of reinforcement formula Chapter I beam Section 1 frame beam First, the calculation of steel reinforcement 1, the upper through tendons The upper perforated rebar (on long rib) through long span span length = + two end bearing anchor value 2, end support negative ribs The negative length of end support: the first row is the anchor value of Ln/3 + end support; The second row is Ln/4 end support anchor value 3, lower reinforcement The reinforcement length = span long + about bearing anchor value 4, lumbar tendon Structure: reinforced structural reinforcement length = span length + 2 * 15d Torsion bars: algorithm with through bars 5, pull the tendons Tensile length = (Liang Kuan 2 * protective layer) + 2 * 11.9d (seismic bending hook value) + 2D 6, stirrups Stirrup length = (Liang Kuan - 2 * protective layer + beam height -2 * protective layer) + 2 * 11.9d + 8D The number of roots (= stirrup length / spacing zone encryption encryption (+1) * 2 + length / non encrypted area non encrypted area spacing 1) +1 7, hanger Hanger length = 2* anchorage length + +2* oblique beam width +2*50, the height of the frame beam angle of =60 DEG 800mm 800mm angle =45 degrees Two. Calculation of steel reinforcement in middle span 1, the middle support negative ribs Intermediate support negative ribs: the first row is Ln/3 + middle support value + Ln/3; The second row is Ln/4 middle support value Ln/4 Three. Calculation of steel reinforcement at tail span Similar to the calculation of the first span steel bar Second sections of other beams I. non frame beam In 03G101-1, the simple explanation of the reinforcement of non frame beams is different from that of frame beams: 1, the common beam stirrups are no longer to distinguish between encrypted and non encrypted areas; 2, the lower longitudinal anchor into the support, only 12d; 3, the upper longitudinal reinforcement anchor into the support, no longer consider the jud