mould english 汇总.docVIP

compre sion molding 压缩成型flash mold 溢流式模具 plsitive mold 挤压式模具split mold 分割式模具 cavity 型控 母模 core 模心 公模taper 锥拔 leather cloak 仿皮革shiver 饰纹 flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值 self tapping screw 自攻螺丝striper plate 脱料板piston 活塞 cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型 （射出成型用模具） two plate 两极式（模具） well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块 valve gate 阀门浇口 band heater 环带状的电热器 spindle 阀针 spear head 刨尖头 slag well 冷料井 cold slag 冷料渣 air vent 排气道welding line 熔合痕eject pin 顶出针 knock pin 顶出销 return pin 回位销反顶针sleave 套筒stripper plate 脱料板 insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销 eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具 runner system 浇道系统 stress crack 应力电裂 orientation 定向 sprue gate 射料浇口，直浇口 nozzle 射嘴 sprue lock pin 料头钩销(拉料杆) slag well 冷料井 side gate 侧浇口edge gate 侧缘浇口 tab gate 搭接浇口film gate 薄膜浇口 flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口 dish gate 因盘形浇口diaphragm gate 隔膜浇口 ring gate 环形浇口subarine gate 潜入式浇口 tunnel gate 隧道式浇口 pin gate 针点浇口 Runner less 无浇道 (sprue less) 无射料管方式 long nozzle 延长喷嘴方式 sprue 浇口;溶渣此孔做斜顶出模，与后模插穿位成干涉，建议后模插穿位做小，以避开此孔THIS HOLE IS MADE AS LIFTER, IT WILL INTERFER??Through Window OF CORE,SO WE SUGGEST MAKE THROUGH WINDOW OF CORE SMALLER TO AVOID THIS HOLE.2、产品有C倒角孔位，孔位做在前模上THIS PRODUCT HAS C??chamfer, THE HOLE SHOULD BE MADE IN CAVITY.3、此两处螺牙做两个斜顶出模，对模具寿命存在危险，建议分成4个螺牙，做四个斜顶出模IT WILL AFFECT MOULD LIFE-TIME IF THESE TWO SCREW??MADE BY TWO LIFTERS,WE SUGGEST DIVIDED INTO 4 SCREWS, MAKE 4 LIFTERS TO EJECT.Make this hole as lifter, which interferes with core insert place. We suggest make smaller place to avoid this hole2. This product has C undercut hole, make the hole on the cavity3. It will affect mold life if make two lifters at this two threads. So we suggest making four threads and four lifters.FYI 01.模具须用多大吊机才可搬动Crane capacity and loading clearance.。102.经流道及变形电脑模拟分析。Conduct mold flow mold warp a