STC404AS AD 比较器 中断应用.docVIP

STC404AS AD 比较器 中断应用 #includeintrins.h //#includereg52.h #includeSTC15W.h #includesys.h #define uint unsigned int #define uchar unsigned char #define FOSC L #define T0MS (65535-FOSC/12/1000) #define AD0 68 #define AD11 68 #define AD12 98 #define ON 1 #define OFF 0 bit P37_flag; bit T0_flag; bit T01_flag; bit CMP_flag; bit adcnt; bit AD0_flag; bit AD1_flag; bit k; bit pp; bit POUT; bit flag; bit s6_flag; uint t0_cnt; uint t0_cntcnt; uint sum; uchar sum_num; uint sum1; uchar sum_num1; uchar cmcnt; uchar AD0_flag_cnt; uchar AD10_flag_cnt; uchar AD11_flag_cnt; uchar ad0; uchar ad1; uchar CMP_flag_cnt; uchar cmp_cnt; uint ad_cnt; uchar AD_result; uchar AD_result1; void delay() { uint i,j; for(i=0;i100;i++) for(j = 0;j 120; j++) ; } void init(void); void init(void) { AUXR =~0X80; TMOD = 0X00; CMPCR1 = 0; CMPCR2 = 0; TH0 = T0MS 8; TL0 = T0MS; EA = 1; ET0 = 1; CMPCR1 = ~PIS; CMPCR1 |= CMPOE; CMPCR1 |= NIS; CMPCR1 |= CMPEN; CMPCR1 |= PIE; CMPCR2 = ~DISFLT; EADC = 1; P1M1 = 0X03; P1M0 = 0x10; PT0 = 1; PADC = 0; //ADC中断优先级高； P1ASF =0X03; // ADC_CONTR = ADC_SPEEDLL | ADC_START | ADC_POWER; P37_flag = P37; //正常情况下，此2位都为0；特殊情况，都为一；此句消抖 POUT = 0; //初始化输出为0，不加热。当P37电平变化时才开始加热 } void main() { init(); while(1) { if(T0_flag) P14 = ON; else P14 = OFF; if(P37 != P37_flag) { P37_flag = !P37_flag; //每次按键按下，标志位都取反 //第一次按键按下，标志为一，开始加热，可避免按键电路上电误操作 POUT = !POUT; } if(POUT) { EA = 1; if(pp) { pp = 0; t0_cntcnt = 0; } CMPCR1 |= CMPEN; //比较器使能 TR0 = 1; //启动T0定时器 //ADC_CONTR |=ADC_SPEEDLL | ADC_START | ADC_POWER | adcnt; } else { TR0 = 0; CMPCR1 = ~CMPEN; t0_cnt = 0; //定时器输出定时参数清零 t0_cntcnt = 0; //定时器参数清零 T0_flag = 0; ADC_CONTR = 0; AD0_flag = 0; AD1_flag = 0; s6_flag = 0; EA = 0; } } } void cmp_isr(void) interrupt 21 { CMPCR1 = ~CMPIF ; if