基站的时隙分配.pptVIP

NOKIA TRAINING THE CONNECTING PEOPLE 传输板的设置及时隙分配 *********common settings and checkings *reset of cu and xu m:9,6,1,99,1 m:9,6,1,99,59 m:9,6,1,99,1 m:9,6,2,99,59 *default setting m:6,6,121 *network topology CHAIN m:6,2,1 *baud rate 9600 m:6,1,1,9600 *TMC address 1 m:6,1,2,1,1 *OM configuration ON m:6,1,4,1 *control time-out 10 MIN m:6,1,7,10 *data hybrid OFF m:6,1,8,2 *timing priority 1 RX1 CLK m:6,3,2,1,1 *timing priority 2 INTERAL m:6,3,2,2,5 *synchronization output MASTER CLK m:6,3,3,1,4 *2m cross connection LIF1-3DIR1-3 m:6,7,1 *meas.output signal DIR1 RX 2M CLK m:6,9,1,4 **********端口1的设置 *use of 2m interface in use m:6,5,1,6,1 *CRC in use (B.B) m:6,5,1,2,1 *use of data channel not in use m:6,5,1,3,1,1 *fixed 1 bits 4,5,6,7,8 m:6,5,1,3,2,4 m:6,5,1,3,2,5 m:6,5,1,3,2,6 m:6,5,1,3,2,7 m:6,5,1,3,2,8 *BER 10E-3 A,S,FEA,AIS m:6,5,1,4,1,1 *FEA S *BER 10E-6 10 sec. m:6,5,1,8,10 **********端口2的设置 *use of 2m interface in use m:6,5,2,6,2 *CRC in use (B.B) m:6,5,2,2,1 *use of data channel not in use m:6,5,2,3,1,1 *fixed 1 bits 4,5,6,7,8 m:6,5,2,3,2,4 m:6,5,2,3,2,5 m:6,5,2,3,2,6 m:6,5,2,3,2,7 m:6,5,2,3,2,8 *BER 10E-3 A,S,FEA,AIS m:6,5,2,4,1,1 *FEA S m:6,5,2,4,2,1 *Rec.AIS B+S alarm m:6,5,2,4,3,2 *BER 10E-6 10 sec. m:6,5,2,8,10 标准时隙分配命令 ************common branching table m:6,4,4,1 m:6,4,1,1,1,2,1,1,1-24,1-24 m:6,4,1,1,1,2,1,1,25--125678,25--125678 m:6,4,1,1,1,2,1,1,25--34,31--12 m:6,4,1,1,1,2,1,1,26-30,26-30 m:6,4,2,1 标准时隙分配表 当使用命令m:6,4,0,0后，显示的界面如下： DIR1 DIR2 DIR3 D-BUS 1-24 1-24 25--1256 25--1256 25--34 31--12 26-30 26-30 6+6配置 ************common bra