LCD TV主观评价标准(机构部分).docVIP

东莞荣电数码科技有限公司　LCD TV主观评价标准（机构部分） 检测内容 评测标准 不合格等级 实测结果 1.钣金件　Plate parts 刮伤　Scratch 由外力所造成，在产品的表面呈现线性刮痕，如果刮伤之情形为弧形，先以软线观测再转为直线方式量测之。 Due to external force,occur linear scratch on product surface.If the scratch is a curve ,observe by soft wire first then measure by straight line. 1.内部结构件刮伤限制长15m宽0.13mm, 不超过3条 2.外观件不允许 B 4.3.1.2 擦伤　Abrasion 由于材料表面相互摩擦，然后造成产品表面粗糙与形成不规则区域。 Resulted from rubbing between surface of material,coarse and irregular area occur on the surface of product. 1. 内部结构件擦伤不超过3条 2.外观件不允许 B 凹陷/凸块/撞痕　Dent/Bulge/Hit 材料表面经由外部力量影响，所造成表面之凹陷或凸起，至于异常之尺寸与形状则未明确。 Resulted from external force,dent or bulge occur on the surface of product,the irregular size or shape was on specified. 1. 内部结构件平整度不超过2mm/100mm,不影响组装 2.外观件不允许 B 黑色斑点　Black spot 造成之原因为不洁物或在成形作业中之作业条件不佳，黑色之斑点出现于产品表面。 Resulted from impurity or worse operation-condition in injection process,black spot occurs on the surface of product. 1. 内部结构件不超过3个 外观件有不可擦拭之斑点不允许 B 水痕　Water spot 干燥作业未完成或者是钣件上之水未清理干净。 Drying process is not completed yet or water is not clean in sheetmetal part. 面积不超过100mm^2 外观件不允许 C 白色锈斑　White speck 钣件表面镀锌层氧化至产品内层，然后产生白色粉沫。 Zinc layer is oxidized into inner layer of surface of sheetmetal part,then white powder occurs. 1.内部结构结构件面结不超过20MM^2 2.外观件不允许 B 变形　Deformation 由于产品表面受到外部力量影响使本体扭曲，并导致不规则形状之发生。 Resulted from suffering external force on the surface of product,the body is twisted and irregular shape occurs. 1. 内部结构件平整度不超过2mm/100mm,不影响组装 2.外观件不允许 A 氧化　Oxidation 钣件材料与空气和水产生化学作用，并在钣件表面出现红棕色之氧化物。 Resulted from chem.ical reaction between sheetmetal part and air/water,oxide in red-brown color occurs on its surface. 1.内部结构结构件面结不超过20MM^2 2.外观件不允许 B 模具缺陷痕迹　Molding spot 由于模具之缺陷导致在成形过程中造成钣件之瑕疵，所以其凹陷点发生在每个冲压钣件位置皆相同。 Resulted from tooling defect,drawback occurs on the process of sheetmetal and these dent spots occur at the same location with regart to every punched parts. 1. 内部结构件平整度不超过2处,不影响组装 2.外观件不允许 B 毛边　Bur 钣件经由铸造、裁切、钻孔、冲压重工作业，导致钣件表面发生粗糙或者钣件边缘呈现锐利之情形。