主要施工方案参考国内同类型机组-建筑施工组织设计大全G.DOC

海萨2x600MW锅炉主要施工方案 Hisar2×600MW Boiler Main Erection Plan 本期建设规模2×600MW燃煤发电机组。锅炉由ＳＥＣ提供。锅炉为亚临界参数、强制循环、一次中间再热、单炉膛平衡通风、固态排渣、露天布置、全钢构架的∏型汽包炉。∏ type drum boiler of a subcritical parameter, pump circulation, single reheat, single furnace balance draft, dry slagging and hypaethral placement. 锅炉施工方案锅炉为上海电气集团生产的亚临界参数、、一次中间再热、单炉膛平衡通风、固态排渣、露天布置、全钢构架的∏型汽包炉。The Boiler shall be supplied by SEC. The boiler is all steel structural ∏ type drum boiler of a subcritical parameter, pump circulation, single reheat, single furnace balance draft, dry slagging and hypaethral placement. 1 施工场地及主吊机械.1 施工场地布置锅炉组合场布置按总平面布置图，组合场内布置0t龙门吊锅炉受热面的大部分组合工作安排在此完成。Boiler assembly yard will be arranged as per general layout drawing. Four 50T gantry cranes will be provided respectively. Assembly of most heating surface structures will be done in this area. 1.2 施工机械选择根据本工程锅炉的结构特点，以及我公司的机械状况，选用以下机械作为锅炉主要施工机械。Gthe boier and mechanical capacity of our company, we chose plants below as our main construction equipmemnts. 序号机械名称机械型号数量 1 圆筒吊cylindrical crane FZQ/80t 2 2 履带吊CC1400 1 3 龙门吊0t 4 4 履带吊 CC2500 1 5 劳辛格Stand-jack system 200t 2 6 C7050/20t 3 (1) FZQ2000/ 80T圆筒吊 FZQ/ 80T cylindrical crane FZQ2000圆筒吊做为附吊机械，筒身高度m，采用60m臂长工况，主要负责锅炉本体部件的吊装工作。FZQcylindrical crane is arranged as auxiliary hoisting plants, which is designed to hoist boiler components (crane body height 102m , length of jib 60m). (2) 250t履带吊 250tCC1400/250t履带吊为锅炉主吊机械，采用SW塔式工况，后配重t，主臂角度85度：主副臂：36m；最大作业半径42m，负荷2t；最小作业半径m时，负荷为t。CC1400/250 Crawler cranes are designed as main boiler hoisting euqipment, adopting SWSL tower working conditions, with a banlance weight of 40t and main jib angle of 85°; length of main auxiliary jib,72+36m, max working radius 42m,load 27t;min working radius 24m,load 39t. 吊装主要内容为：a. 锅炉钢架吊装。B b. 锅炉受热面吊装、空气预热器吊装。Bc.烟、风、煤管道安装 Flue gas,air,coal piping erection. d. 根据现场实际换工况用于大件设备的卸车工作。CC1400/250t履带吊性能表(塔式、后配重t工况)主附臂(主臂角度85o)：m+36m。CC1400/250t crawler crane performance list(SWSL TOWER type,banlance weight 40