- 1、本文档共66页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
长安大学桥梁工程2015届优秀本科毕业设计——连续刚构桥汇
二 ○ 一 五 届 毕 业 设 计
***河
学 院:公路学院
专 业:桥梁工程
姓 名:
学 号:
指导教师:
完成时间:2015.06.14
二〇一五年六月
摘 要
根据设计任务书要求,依据现行公路桥梁设计规范,综合考虑桥位的地质、地形条件,提出了独塔斜拉桥、上承式钢管混凝土拱桥和预应力混凝土连续钢构三个比选方案。按“安全、经济、适用、美观和有利于环保”的桥梁设计原则,分析了三个方案的优缺点。推荐预应力混凝土连续刚构作为设计方案。推荐方案以基本设计理论为基础,参考国内外成功的大跨连续钢构桥,拟定了的跨径,主梁采用1.8次抛物线变梁高的单箱单室箱主梁,桥墩为双薄壁空心墩,桥台为轻型桥台,基础为群桩基础,施工阶段采取挂篮悬臂现浇法。对推荐方案进行了结构细部尺寸拟定,对上部结构和下部结构进行了内力计算、配筋设计及控制截面强度、应力验算,变形验算等。经分析比较及验算结果表明该桥梁设计合理,符合设计任务的要求。
关键词:预应力混凝土连续刚构,钢管混凝土拱桥斜拉桥,悬臂,验算
ABSTRACT
According to the design requirements, the existing design specification of highway bridge, considering the geology and terrain conditions of the bridge site, after preliminary selection, three bridge type schemas are presented, they are cable-stayed bridge, arch bridge and prestressed concrete continuous rigid frame bridge . Then comparing the advantages and disadvantages of three options comprehensively by the philosophy of bridge design as “Security, Economy, Application, Beauty and Environmental Protection”. The PC continuous rigid frame bridge is selected as the recommended scheme after the selections. This project is based on the basic theory of bridge design and take the domestic and international successful designs for example, finally chose a span combination of .The depth of Single cell box girder varies as the second-degree parabola, the pier is a double thin-wall hollow pier, the abutment is light abutment, the foundation is grouped piles foundation,and the the hanging basket cantilever casting construction method. Through drawing up of structure’s dimension and then design the upper and lower part of the structure ,such as calculated the internal force of dead and living load, prestressed steel design, checking the strength and stress of control cross-section. Finally, check for live load deformation. Checked by the comparison and analysis show that the design method of calculation is correct, and the distribution of reinforcement is Reasonable, so this design meet the design requirements.
Key wo
您可能关注的文档
- SmartMad移动广告网络推介方案幻灯片.ppt
- 金融设备研发中试生产项目可行性研究报告汇.doc
- SMT抛料改善报告幻灯片.ppt
- 金银花GAP种植项目可行性研究报告汇.doc
- SMT制程幻灯片.ppt
- 金融投资有限责任公司工作制度汇.doc
- 金银花种植与产业化开发项目可行性报告汇.doc
- SMT工艺流程培训幻灯片.ppt
- 金鹿新城财园9#楼十三至三十一层主体验收会议纪要汇.doc
- SKF润滑知识培训资料幻灯片.ppt
- 第十一章 电流和电路专题特训二 实物图与电路图的互画 教学设计 2024-2025学年鲁科版物理九年级上册.docx
- 人教版七年级上册信息技术6.3加工音频素材 教学设计.docx
- 5.1自然地理环境的整体性 说课教案 (1).docx
- 4.1 夯实法治基础 教学设计-2023-2024学年统编版九年级道德与法治上册.docx
- 3.1 光的色彩 颜色 电子教案 2023-2024学年苏科版为了八年级上学期.docx
- 小学体育与健康 四年级下册健康教育 教案.docx
- 2024-2025学年初中数学九年级下册北京课改版(2024)教学设计合集.docx
- 2024-2025学年初中科学七年级下册浙教版(2024)教学设计合集.docx
- 2024-2025学年小学信息技术(信息科技)六年级下册浙摄影版(2013)教学设计合集.docx
- 2024-2025学年小学美术二年级下册人美版(常锐伦、欧京海)教学设计合集.docx
文档评论(0)