Greenplum-5.0安装.docxVIP

Greenplum 在Linux下的安装1.实验环境1.1.硬件环境Oracle VM VirtualBox虚拟机软件；三台Linux虚拟机：Centos 6.5；数据库：greenplum-db--build-1-rhel5-x86_64.zip。1.2网卡设置?1.3.虚拟机配置1.3.1.基本信息配置?节点?IP?内存?硬盘??master??80??2048M?50G?slave1??81??1024M?50G?slave2??82??1024M?50G?1.3.2.系统相关配置（所有节点）.设置IP地址的命令行方式master示例：填写ip地址、子网掩码、网关、DNS等；slave1、slave2参照master修改ip地址即可。[root@localhost~]#vim /etc/sysconfig/network-scripts/ifcfg-eth0DEVICE=eth0TYPE=EthernetUUID=f16c7950-fcae-486c-8230-7b181e08bf6dONBOOT=yesNM_CONTROLLED=yesBOOTPROTO=noneHWADDR=08:00:27:21:47:1DIPADDR=80PREFIX=24GATEWAY=DNS1=80DEFROUTE=yesIPV4_FAILURE_FATAL=yesIPV6INIT=noNAME=System eth0.关闭防火墙修改/etc/selinux/config文件:[root@localhost ~]#/sbin/chkconfig iptables off[root@localhost ~]#vim /etc/selinux/configSELINUX=disabled# SELINUXTYPE= can take one of these two values:# ????targeted - Targeted processes are protected,# ????mls - Multi Level Security protection.SELINUXTYPE=targeted检测防火墙状态：[root@localhost ~]#/sbin/chkconfig --list iptablesiptables ????? 0:off 1:off 2:off 3:off 4:off 5:off 6:off?.修改主机名和IP映射master示例：修改HOSTNAME为master;slave1、slave2参照master，修改为slave1及slave2。[root@localhost ~]#vim /etc/sysconfig/networkNETWORKING=yesHOSTNAME=master所有节点hosts增加以下信息[root@localhost ~]#vim /etc/hosts localhost localhost.localdomain localhost4 localhost4.localdomain4::1 ??????localhost localhost.localdomain localhost6 localhost6.localdomain680 master81 slave182 slave2所有节点重启服务器：reboot?.系统参数配置包括共享内存、网络、用户限制等，修改或添加/etc/sysctl.conf。[root@master ~]#vim /etc/sysctl.conf?#for greenplum beginxfs_mount_options = rw,noatime,inode64,allocsize=16mkernel.shmmax = 500000000kernel.shmall = 4000000000kernel.shmmni = 4096kernel.sem = 250 512000 100 2048kernel.sysrq = 1kernel.core_uses_pid = 1kernel.msgmni = 2048net.ipv4.tcp_tw_recycle = 1net.ipv4.tcp_max_syn_backlog = 4096net.ipv4.conf.all.arp_filter = 1net.ipv4.ip_local_port_range = 1025 65535dev_max_backlog = 10000vm.overcommit_memory = 2#for greenplum end配置/etc/security/limits.conf文件[root@master~]#vim /etc/security/limits.conf?