- 1、本文档共44页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
矿泉水饮料瓶盖注射模具及成型零件加工工艺设计
[摘要] 本设计是对给定的材料为PP小尺寸,一般精度的矿泉水饮料瓶盖塑件进行模具设计。在综合研究了经济性、零件的成型工艺以及复杂性等诸多因素的基础上进行成型与工艺的分析与计算。文中还对注塑模具成型零件和其他相关零件的选择原则及选择方法进行了说明。期间借鉴了与塑料模具有关的文献再加上翻阅各种指导书籍,并通过大量的计算以确定模具的结构和尺寸,还在指导老师的悉心关怀和耐心指导下进行多次的反复修改,最终画出了装配图和零件图。
最终确定矿泉水饮料瓶盖塑件的设计方案,主要包其注塑模的设计的过程、以及注塑模主要零部件的设计过程等。
[关键词]注塑模具设计;模具结构;塑料瓶盖
Abstract
This design is for a given material for PP small size, the general accuracy of the charger shell plastic parts for mold design. Within consideration of the economy, parts of the molding technology and complexity, and many other factors in the molding process on the basis of the analysis and calculation. It also of injection mold shaping parts, and other related parts to illustrate the selection principle and selection method. During to refer to a lot of useful information related to injection mold and leaf through all kinds of manual, And through calculation to determine the mold structure and size, Through continuous calculation and modification, And in guiding the teachers careful care under the guidance and patience to constantly modify again and again, Finally the sure to draw the assembly drawing and part drawing.
Make sure the design of the charger shell, namely the mold with one module and two cavities, side core-pulling design scheme. Then focuses on the solution, this paper mainly includes the side core-pulling of plastic parts and injection mold design process, key points of injection mold design of main components.
Key words: Injection mold design; The mold structure; Plastic bottle cap
目录
1 概述 1
1.1 课题来源 1
1.2 课题的研究目的 1
2 塑件结构工艺性分析 3
2.1 塑件造型 3
2.2塑件分析 4
2.2.1.塑件设计要求 4
2.2.2 塑件结构分析 4
2.2.3 脱模斜度 4
2.3 塑件原材料分析 5
2.3.1 PP材料特性 5
2.3.2 PP塑料主要用途 5
2.3.3 塑料材料成型性能 5
2.3.4 PP成型温度条件 6
2.3.5. 塑件的公差与表面质量 7
3 拟定注塑模具结构 8
3.1 分型面的确定 8
3.2型腔数目的确定 8
3.3 拟选注塑机型号 9
3.3.1 注射量的计算 9
3.3.2 选择注塑机 10
4 注塑机相关参数的校核 10
4.1最大注射量的校核 11
4.2注射压力的校核 11
4.3锁模力的校核 11
4.4注射模安装尺寸的校核 12
5 浇注系统的设计 13
5.1主流道 14
5.2分流道 14
5.3浇口的设计 15
5.4 浇注系统的平衡 16
6 温度调节系统的设计 16
7 结构零部件的设计 17
7.1
您可能关注的文档
- 第5篇 审计抽样.ppt
- 第5篇 压电传感器.ppt
- 第3章 电子商务项目的范围及计划.ppt
- 第5篇 支付结算业务.ppt
- 第5篇-旅游者的旅游动机.ppt
- 第3章 各项费用的归集与分配.ppt
- 第5章 腌渍与烟熏.ppt
- 第3章账户及复式记第一节.ppt
- 第06节 利用数组处理批量数据.ppt
- 第07篇 谈判策略.ppt
- 第十一章 电流和电路专题特训二 实物图与电路图的互画 教学设计 2024-2025学年鲁科版物理九年级上册.docx
- 人教版七年级上册信息技术6.3加工音频素材 教学设计.docx
- 5.1自然地理环境的整体性 说课教案 (1).docx
- 4.1 夯实法治基础 教学设计-2023-2024学年统编版九年级道德与法治上册.docx
- 3.1 光的色彩 颜色 电子教案 2023-2024学年苏科版为了八年级上学期.docx
- 小学体育与健康 四年级下册健康教育 教案.docx
- 2024-2025学年初中数学九年级下册北京课改版(2024)教学设计合集.docx
- 2024-2025学年初中科学七年级下册浙教版(2024)教学设计合集.docx
- 2024-2025学年小学信息技术(信息科技)六年级下册浙摄影版(2013)教学设计合集.docx
- 2024-2025学年小学美术二年级下册人美版(常锐伦、欧京海)教学设计合集.docx
最近下载
- 数系的扩充与复数的概念教学设计.doc VIP
- 结婚函调报告表.docx
- 氢燃料电池用全氟型质子交换膜.pdf VIP
- 人教版数学二年级上册第四单元《表内乘法(一)》单元整体作业设计.docx VIP
- 2.5 跨学科实践:制作隔音房间模型(课件)人教版(2024)物理八年级上册.pptx VIP
- 大学生心理健康教育.pptx VIP
- 高中信息技术 粤教版必修2《信息系统的安全风险防范》(单元教学设计).pdf VIP
- Unit 2 Reading for writing课件 外研版(2024)七年级英语上册.pptx VIP
- 教科版物理八年级上册第六章 质量与密度 大单元整体学历案教案 教学设计附作业设计(基于新课标教学评一致性).docx
- 非自然叙事学_尚必武.pdf
文档评论(0)