毕业设计论文）-热吸成型机辅机设计（全套图纸三维）.docVIP

轴承衬套自动化装配机的设计 题 目 热吸成型辅机毕业设计专 业 学生姓名 ╳╳╳ 学 号 指导教师 ╳╳╳ 论文字数 完成日期 2015年4月 摘 要聚氯乙烯为白色蜡状半透明材料，柔而韧，可分为低密度聚氯乙烯(LDPVC)和高密度聚氯乙烯(HDPVC)两大类，LDPVC是由乙烯在高压全套图纸，加153893706(98-250MPa)下制得，密度大约在0．91-0．92g／m3之间，HDPVC由乙烯在1．0MPa压力下聚合而成，密度较高，约为0．94-0．96 g／cm3t 。聚氯乙烯无毒，具有优异的介电性能，它的玻璃化温度约为一125~C。聚氯乙烯具有优异的化学稳定性，室温下能耐酸和碱，但容易受光氧化、热氧化，在紫外线下还可发生光降解。聚氯乙烯还具有优异的力学性能，其结晶部分赋予聚氯乙烯较高的强度，非结晶部分赋予其良好的柔韧性 。在热塑性材料的软化温度和熔融温度之间使其在纵向或横向拉伸，使分子具有定向性，冷却后使定向性定型，称为定向技术或拉伸技术。拉伸膜(又称拉伸回缩膜、缠绕膜)是一种在常温下具有良好弹性和耐穿刺性能的膜材料，拉伸倍率高达200％-300％，并具有较大的回缩性、持久的束紧力、适宜的透气和透湿性等。。关键词: 聚氯乙烯；热拉伸；透气AbstractPolyvinyl chloride as?a white waxy?translucent material,?soft and tough,?can be divided into?low densitypolyvinyl chloride?(LDPVC)?and high density?polyvinyl chloride?(HDPVC)?two,?LDPVC is composed ofethylene?at high pressure?(98-250MPa)?was?about 0.91-0.92g?/ m3,?the density of?between?HDPVC,?theethylene polymerization?under the pressure of 1.0MPa?and?a,?the higher density,?is about 0.94-0.96?g?/ cm3t.Polyvinyl chloride?nontoxic,?has?excellent dielectric properties,?glass transition temperature?is about?125~Cit.?PVC?with?excellent chemical stability,?acid?and?alkali?at room temperature,?but?susceptible to?oxidation,thermal oxidation,?ultraviolet?light?degradation?can occur.?PVC?has?excellent mechanical properties,crystallization?of?polyvinyl chloride?with?high strength,?non?crystalline part?has good?flexibility.?Thethermoplastic material?softening temperature?and melting temperature?in the?longitudinal or transversetensile,?the molecule?is directional,?directional?cooling?after?setting,?called?directional technology?or?drawing technology.?Tensile?membrane?(also known as?tensile membrane retraction,?wrapping film)?is a kind of membrane?material with good?elasticity?at ambient temperature?and?puncture resistance,?tensile?rate?as high as 200%-300%,?and has?retracted,?fastening force,?lasting?for?air permeability a