（毕业学术论文设计）-四杆中频数控淬火机床的设计制造.docVIP

杜立闯：四杆中频数控淬火机床总体及上料机构设计 PAGE 2 目录 前言 ………………………………………………………………………………1 1绪论 ……………………………………………………………………………2 1.1淬火机床国内外发展状况…………………………………………………2 1.2四杆中频数控淬火机概述……………………………………………………2 2四杆中频淬火机床总体设计 …………………………………………………4 2.1机床动作流程 ………………………………………………………………4 2.2斜辊传输……………………………………………………………………4 2.3工件进给过程…………………………………………………………………4 2.4中频淬火过程…………………………………………………………………4 2.5机床电气、水循环和气动系统………………………………………………5 3上料传送装置的设计……………………………………………………………5 3.1上料传送装置料架的设计……………………………………………………5 3.2 选取电动机…………………………………………………………………10 3.3 选取减速器…………………………………………………………………10 3.4 链轮的设计…………………………………………………………………11 3.5 轴的设计……………………………………………………………………27 3.6 滚动轴承的设计……………………………………………………………34 3.7 V型滚的设计 ………………………………………………………………36 4 结论……………………………………………………………………………41 致谢 ……………………………………………………………………………42 参考文献…………………………………………………………………………43 附录A 译文 ……………………………………………………………………45附录B 外文文献…………………………………摘要 通过这项研制工作改变了过去同类设备大多依赖进口的局面,可节约大量的购置资金和维修费用,对提高国内抽油杆感应淬火水平具有很大意义。 抽油杆是连接抽油机和抽油泵的传动装置，通过往复运动抽取石油。由于抽油杆自重作用，上部抽油杆承受拉-拉循环载荷，引起表面裂痕扩展，导致疲劳断裂。从文献可知，材料通过热处理可提高疲劳寿命和强度。对于抽油杆，表面的残余压应力与疲劳寿命有关。针对抽油杆的结构特点及热处理工艺的特殊性，研制了ZZJS四杆中频淬火机床。实践证明,它具有如下优点:工件淬硬区层深和硬度分布均匀,淬火变形小,油孔开裂倾向小,能大大减少微裂纹的产生，淬火过程中抽油杆弯曲变形较小。目前,四杆中频淬火机床在山东滨州石油机械公司投入使用,已生产出合格产品,符合美国石油协会API标准，使用效果良好。 关键词：热处理设备;淬火机床;抽油杆;淬火过程 Abstract Changed the past similar equipment through this development work mostly to rely on the import the aspect. May save the massive purchase fund and the maintenance cost, To raises the domestic oil extraction rod induction hardening level to have the very big significance. The oil extraction rod is connects the pumping unit and the oil pump transmission device, Through reciprocal motion extraction petroleum. As a result of oil extraction rod dead weight function. Upside oil extraction rod withstanding pulls - pulls the cyclic load, Causes the surface crack expansion, Causes the endurance failure. May know from the literature, The material may enhance the fatigue life and the intensity through the heat treatment. May know from the literature, The material may enha