1000t-d印染废水排放处理工程设计.docVIP

1000t/d印染废水排放处理工程设计 摘 要：本文是对规模1000t/d，进水CODCr=600mg/L，BOD5=120mg/L，SS=200mg/L，色度为200倍的印染废水进行排放处理的工程设计。相比其他工业废水，印染废水中盐、氯化物、硫和金属离子的含量高，且因其高COD和高色度，成为了最难处理的工业废水之一。本文根据印染废水可生化性较低的特点，采用了“物化+生化”的处理方法，使出水水质达到国家标准，最终废水接入市政污水管网纳管排放。 关键词：印染废水；废水处理；A/O工艺 The design of discharge treatment works for printing and dyeing wastewater with 1000t/d Abstract: This article describes the design of discharge treatment works for the printing and dyeing wastewater of 1000t/d inflow, 600mg/L CODCr, 120mg/L BOD5 and 200mg/L SS. Compared to other industrial wastewater, mostly dyeing wastewater, which contains salt, chloride, bromide, metal ions, and sulfur, is one of the most hard-to-treat kinds of wastewater with high COD and high chroma. This article, which is based on the low biodegradability of dyeing wastewater and its reuse requirement, uses the A/O process to make water quality meet the national standards .nally, the treated water is discharge into the municipal sewage network. Keywords: Printing and dyeing wastewater; Wastewater treatment; A/O Process 目录 TOC \o 1-3 \h \z \u HYPERLINK \l _Toc388725136 1.引言 PAGEREF _Toc388725136 \h 1 HYPERLINK \l _Toc388725137 1.1设计背景 PAGEREF _Toc388725137 \h 1 HYPERLINK \l _Toc388725138 1.2 印染废水处理技术进展 PAGEREF _Toc388725138 \h 1 HYPERLINK \l _Toc388725139 1.3设计目标 PAGEREF _Toc388725139 \h 2 HYPERLINK \l _Toc388725140 1.4基本思路 PAGEREF _Toc388725140 \h 3 HYPERLINK \l _Toc388725141 2.工程概况 PAGEREF _Toc388725141 \h 4 HYPERLINK \l _Toc388725142 2.1设计依据 PAGEREF _Toc388725142 \h 4 HYPERLINK \l _Toc388725143 2.2设计原则 PAGEREF _Toc388725143 \h 4 HYPERLINK \l _Toc388725144 2.3水质特征与处理要求 PAGEREF _Toc388725144 \h 4 HYPERLINK \l _Toc388725145 3处理工艺流程 PAGEREF _Toc388725145 \h 6 HYPERLINK \l _Toc388725146 3.1工艺流程选择依据 PAGEREF _Toc388725146 \h 6 HYPERLINK \l _Toc388725147 3.2处理工艺比选 PAGEREF _Toc388725147 \h 6 HYPERLINK \l _Toc388725148 3.3处理工艺流程 PAGEREF _Toc388725148 \h 8 HYPERLINK \l _Toc388725149 3.4 预期处理效果 PAGEREF _Toc388725149 \h 9 HYPERLI