10000t-d印染废水排放及回用处理工程设计.docVIP

- PAGE \* MERGEFORMAT 1- 10000t/d印染废水排放及回用处理工程设计 摘 要：本文为规模10000t/d印染废水进行排放及部分回用的工程设计书，其进水为CODCr=2500mg/L，BOD5=750mg/L，SS=600mg/L，色度为400。本文针对印染废水的特性及回用目的进行设计，采用“物化+生化+MBR+RO”的处理工艺工程占地面积5570.48m2，总投资3856.63万元，运行成本3.04元/吨废水。设计出水水质满足《纺织染整工业水污染物排放标准》（GB 4287-2012)中的间接排放标准，回用水水质满足《纺织染整工业回用水水质》（FZ/T 01107-2011）的标准。最终废水接入市政污水管网。 关键词：印染废水；回用；MBR；RO The design of discharged and reused treatment project for printing and dyeing wastewater with 10000t/d Abstract: The paper makes the discharged and reused treatment project design based on the dyeing wastewater, whose inflow is 10000t/d, CODCr=2500mg/L, BOD5=750mg/L, SS=600mg/L. For printing and dyeing wastewater are harder to biochemical treatment and reused purpose, adopt physicochemical + biochemical + MBR + RO process. Gives a feasible scheme, both of The quality of the discharged water and reused water are better than national standard. Project covers an area of 5570.48 m2, with a total investment of 38.5663 million yuan, the operation cost 3.04 yuan/tons of waste water. The final water discharges into the municipal wastewater pipelines. Keywords:Printing and dyeing wastewater; Reuse; MBR; RO - PAGE 29 - 正文目录 TOC \o 1-3 \h \z \u HYPERLINK \l _Toc388443614 1引言 PAGEREF _Toc388443614 \h 1 HYPERLINK \l _Toc388443615 1.1设计背景及意义 PAGEREF _Toc388443615 \h 1 HYPERLINK \l _Toc388443616 1.2设计目标 PAGEREF _Toc388443616 \h 1 HYPERLINK \l _Toc388443617 1.3基本思路 PAGEREF _Toc388443617 \h 1 HYPERLINK \l _Toc388443618 2工程概况 PAGEREF _Toc388443618 \h 3 HYPERLINK \l _Toc388443619 2.1设计依据 PAGEREF _Toc388443619 \h 3 HYPERLINK \l _Toc388443620 2.2设计原则 PAGEREF _Toc388443620 \h 3 HYPERLINK \l _Toc388443621 2.3设计水量水质与排放标准 PAGEREF _Toc388443621 \h 3 HYPERLINK \l _Toc388443622 3处理工艺流程 PAGEREF _Toc388443622 \h 5 HYPERLINK \l _Toc388443623 3.1选择工艺流程的依据 PAGEREF _Toc388443623 \h 5 HYPERLINK \l _Toc388443624 3.2 同类废水处理技术现状 PAGEREF _Toc388443624 \h 5 HYPERLINK \l _Toc388443625 3.3处理工艺比选 PAGEREF _Toc388443625 \h 7 HYPERLINK \l _Toc38