脉冲放电脱硫反应器电参数测量及结构优化-环境工程专业毕业论文.docxVIP

辣坤魄挚脱硫艇艨器电参数测量及结构优化摘要 辣坤魄挚脱硫艇艨器电参数测量及结构优化 摘要 零漾鼷运矮实验方法瓣稼黻毫{髓等离予体线—蔽式l莞璇爱盛嚣静放电特稳、宅 极配鼹形式对脱硫效率的影响以及脉?中自邕量沿放电线酶终输进行了较为深入秘系统孥研 究，强豹楚为该按零豹工监纯波瘸强擞辩擎袄蕹。圭嚣掰究疼容稻绩谂脊： 1、在爨漏、空气介质条件下，研究了不同初级电胍、不同成形电容匹配、不同线 板间距、不蚓故电极冬#g基等因素对放电特性的影嘲，褥期了反应爨的放毫娥捧：默淀瞧 值电藤、基簇和拖蓬毫压随敬电极邻躐的增大先减小，然后增大；脉冲能爨则随放电极 令嘲i的增大毙增大，然露≯裁小。劳稷撵零实验结蓉，褥感了爱您黼薯卜啜续{訇绕傀愆置 翡经验公式b=0．3c+3．75(式巾b为敖跑线闻躐，c为线—板闻躐，单位酃是cm)。 2、经过X撤电极在不同脉冲峰值电压、不同来端噬酉已、不同放电线感襁下进杼的能 量衰减实骏蹬究。褥载了麓藩躲滓§篆羹燕毫晕放电壤土淤行渡形式传播、藏减静麓律： 高压脉冲能缀沿电晕线迅速衰减，脉冲波形显著畸变；峰值电压越离，电聚线越细，放 电越谶，衰减越捷；电孥境遥端受行波及射影响较大。妫霉出：在遴舒反疲器豹设计时， 为提胬脱硫效率和能纛利用率，合理设计反应器的尺寸，提高反艨器的褴价}￡，放电线 的长度不宜避长，一般不应越过10m。 3、花碉气量为200Nm3／h烟气脱黼戡骈亍了脱硫实验研究，通过脱硫率与电极 结构和电源氍配关系的研究结果，验证T反应器结构优化的经验公式，并提高了脱硫效 率。 羧疆诞：辣；枣毫爨教电：敷龟特性；爱旋器缝擒蜣纯；笺鏊传骧；羰蘧臻 咏冲电晕脱硫菔应器屯参数测羹投结构优化Abstract 咏冲电晕脱硫菔应器屯参数测羹投结构优化 Abstract In this paper,detailed studies were made On discharge characteristics ofpulse corona reactor,the influences of electrode configuration On desulfufization and磴se energy transmission along the discharge wires for industrial application of the technique。nle following results were obtained． 1．The influence factors(such as voltage,pulse forming capacitance，wire—to—plate spacing，w轻争晒一诚糟spacing)on蠢s。ha￡菖e characteristics are researched on the condition of room temperature and air medium,and the discharge characteristics of reactor are obtained：the peal【value，minimum value and wave tail of pulse voltage firstly increase with the increase of wSre-to-wire spacing，then all decrease；but pulse energy firstly decreases with the increase of wire-to-wire spacing,then increases。According tO experimental conclusion，the experimental formula of the optimized electrode configuration，b=0．3c+37．5(b，wire-to-wire spacing；C，wire-to-plate space)is gotten． 2．The attenuation and distortion law of pulse voltage transmitting on discharge electrode is obtained by research of energy attenuation on different conditions(such as voltage，terminal matching and diameter)．Pulse voltage sharply decreases due to the corona．The higher the pulse voltage，the thinner